SIP Type SSR for Medium Power Control - Absolute Maximum Ratings (Ta = 25°C) - Electrical Characteristics

Q: What are the RMS on-state current ratings for S202SE1/S202SE2 and S216SE1/S216SE2?

S202SE1/S202SE2 provide 8Arms at Tc ≤ 80°C (with heat sink), while S216SE1/S216SE2 provide 16Arms at Tc ≤ 60°C (with heat sink).

Q: What isolation voltage and insulation conditions are specified between input and output?

The isolation voltage Viso is 3,000V rms, and the document specifies insulation distance, creepage distance, and spacing requirements, with a note to use an insulation sheet when using an external heat sink. It also includes an AC 60Hz dielectric withstand test condition with defined humidity and grounding/shorting instructions.

Q: Which electrical characteristics and thermal ratings are included for system design?

The document provides forward voltage and reverse current, on-state voltage, holding current, critical rise rate of OFF-state voltage and commutating OFF-state voltage, zero-cross voltage, transfer characteristics including minimum trigger current and isolation resistance, turn-on/turn-off times at AC 60Hz, and thermal resistance (junction-to-case and junction-to-ambient), plus current graphs versus ambient and case temperatures.

Oct 12, 2026

Upload by anakgang17

SIP Type SSR medium-power control devices S202SE1/S202SE2 and S216SE1/S216SE2 are specified with European safety compliance, insulation distance/creepage/spacing requirements, and defined RMS on-state current limits under specified case temperatures and heatsink conditions. The document lists isolation voltage ratings between input and output, certification references (TU, UL, CSA), approved applications for copiers and laser beam printers, and detailed absolute maximum ratings. It further provides electrical characteristics such as forward voltage, reverse current, on-state voltage, holding current, critical dV/dt parameters, zero-cross voltage, transfer characteristics, isolation resistance, switching times, and thermal resistance, plus performance graphs versus ambient and case temperatures.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages4

Reading Time10 min

AccessFree to download

Features

Safety standards and isolation requirements

RMS on-state current ratings

Isolation voltage and approvals

Applications

Copiers

Laser beam printers

Line-up

Zero-cross circuit options

Absolute Maximum Ratings

Input and output ratings

Operating and storage temperatures

Soldering temperature

Electrical Characteristics

Input parameters

Output and switching behavior

Thermal resistance and graphs

S202SE1/S202SE2 S216SE1/S216SE2 ■ Features 1. Comforms to European Safety Standard ( EN60950) (Need of the insulation sheet when mounting external heat sink) Internal insulation distance : 0 .4mm or more Creepage distance : 5mm or more Space distance : 4mm or more 2. RMS ON-state current S202SE1 / S202SE2 : 8Arms at Tc <= 80˚C ( with heat sink) S216SE1 / S216SE2 : 16Arms at Tc <= 60˚C ( with heat sink) 3. Isolation voltage between input and output ( Viso : 3 000V rms ) 4. Approved by TU. .V, No. R9051479 5. Recognized by UL, No. E94758 ( S202SE1 / S202SE2 ) Approved by CSA, No. LR63705 ( S202SE1 , S202SE2 ) ■ Applications 1. Copiers 2. Laser beam printers ■ Line-up | | RMS ON-state current | | | --- | --- | --- | | | MAX. 8Arms | MAX. 16Arms | | No built-in
Zero-cross circuit | S202SE1 | S216SE1 | | Built-in
Zero-cross circuit | S202SE2 | S216SE2 | SIP Type SSR for Medium Power Control ■ Outline Dimensions ( Unit : mm ) ■ Absolute Maximum Ratings ( Ta = 25˚C ) | Parameter | | Symbol | Rating | | Unit | | --- | --- | --- | --- | --- | --- | | | | | S202SE1 / S202SE2 | S216SE1 / S216SE2 | | | Input | Forward current | IF | 50 | | mA | | | Reverse voltage | VR | 6 | | V | | Output | RMS ON-state current | IT | *48 | *5 16 | A rms | | | *1Peak one cycle surge current | I surge | 80 | 160 | A | | | Repetitive peak OFF-state voltage | V DRM | 600 | | V | | | Non-repetitive peak OFF-state voltage | V DSM | 600 | | V | | | Critical rate of rise of ON-state current | dIT /dt | 50 | | A/µ s | | | Operating frequency | f | 45 to 65 | | Hz | | *2 Isolation voltage | | V iso | 3,000 | | V rms | | Operating temperature | | T opr | -25 to + 100 | | ˚C | | Storage temperature | | T stg | -30 to + 125 | | ˚C | | *3 Soldering temperature | | T sol | 260 | | ˚C | *1 60Hz sine wave, Tj = 25˚C start *2 AC 60Hz for 1 minute, 40 to 60% RH, Apply voltages between input and output by the dielectric withstand voltage tester with zero-cross circuit.( Input and output shall be shorted respectively) . ( Note) When the isolation voltage is necessary at using external heat sink, please use the insulation sheet. *3 For 10 seconds *4 TC<=80˚C *5 TC<=60˚C “ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.” S202SE1/S202SE2/S216SE1/S216SE2 | ■ Electrical Characteristics | | | | | | | ( Ta = 25˚C ) | | | --- | --- | --- | --- | --- | --- | --- | --- | --- | | Parameter | | | Symbol | Conditions | MIN. | TYP. | MAX. | Unit | | Input | Forward voltage
Reverse current | | V F | IF = 20mA | - | 1.2 | 1.4 | V | | | | | IR | VR = 3V | - | - | 10-4 | A | | Repetitive peak OFF-state current | | | I DRM | VD = V DRM | - | - | 10-4 | A | | ON-state voltage | | S202SE1 / S202SE2 S216SE1 / S216SE2 | V T | IT = 2Arms
IT = 16Arms | -
- | -
- | 1.5
1.5 | V rms | | Output Holding current | | | IH | - | - | - | 50 | mA | | Critical rate of rise of OFF-state voltage | | | dV/dt | VD = 2/3V DRM | 30 | - | - | V/ µ s | | Critical rate of rise ofcommutating OFF-state voltage | | | ( dV/dt )c | Tj = 125˚C, VD = 400V *6 | 5 | - | - | V/ µ s | | Zero-cross voltage S202SE2 / S216SE2 | | | V OX | IF = 8mA | - | - | 35 | V | | Transfer
charac- | Minimum trigger S202SE1 / S216SE1
current S202SE2 / S216SE2
Isolation resistance | | I FT | VD = 12V, R L = 30 Ω
VD = 6V, R L = 30 Ω | -
- | -
- | 8
8 | mA | | | | | R ISO | DC500V, 40 to 60 % RH | 1010 | - | - | Ω | | teristics | S202SE1 / S216SE1
Turn-on time
S202SE2 / S216SE2
Turn-off time | | t on | AC60Hz | -
- | -
- | 1
9.3 | ms | | | | | t off | AC60Hz | - | - | 9.3 | ms | | Thermal resistance S202

FAQs

What are the RMS on-state current ratings for S202SE1/S202SE2 and S216SE1/S216SE2?

S202SE1/S202SE2 provide 8Arms at Tc ≤ 80°C (with heat sink), while S216SE1/S216SE2 provide 16Arms at Tc ≤ 60°C (with heat sink).

What isolation voltage and insulation conditions are specified between input and output?

The isolation voltage Viso is 3,000V rms, and the document specifies insulation distance, creepage distance, and spacing requirements, with a note to use an insulation sheet when using an external heat sink. It also includes an AC 60Hz dielectric withstand test condition with defined humidity and grounding/shorting instructions.

Which electrical characteristics and thermal ratings are included for system design?

The document provides forward voltage and reverse current, on-state voltage, holding current, critical rise rate of OFF-state voltage and commutating OFF-state voltage, zero-cross voltage, transfer characteristics including minimum trigger current and isolation resistance, turn-on/turn-off times at AC 60Hz, and thermal resistance (junction-to-case and junction-to-ambient), plus current graphs versus ambient and case temperatures.

Oct 12, 2026

Upload by anakgang17