Draw and Interpret Drawing - Module IND MAC1 M01 02 22 - Machining Level-I

Oct 23, 2026

Upload by Bintang

Machining Level-I module “Draw and Interpret Drawing” (module code IND MAC1 M01 02 22) provides structured training for reading, interpreting, and producing technical drawings. The curriculum covers preparation for drawing, including drawing instruments, line reading, measurements, scales, drawing standards, and lettering, followed by activities to construct geometric shapes and develop multi-view projections. It further includes principles of orthographic projection, first-/third-angle projection concepts, 3D pictorial drawing, sectional views, and freehand sketching with key requirements and dimensioning basics. Developed by the Ministry of Labour and Skill.

LanguageEnglish

CategoryExam

FormatPDF

Pages124

Reading Time5 h 12 min

AccessFree to download

Introduction To The Module

Unit One: Prepare For Drawing

Introduction Drawing

Drawing Instruments

Read And Interpreted Lines

Measurements And Scales

Lettering

Unit Two: Draw Simple Drawing

A Series Of Geometric Shapes

Geometrical Construction Problems

Unit Three: Construct Multi-View

Projection View

Sketching Multi View Drawings

3D Pictorial Drawing

Sectional Views Overview

Unit Four: Prepare Freehand Sketch

Free Hand Sketching

Dimensioning

Machining Level-I Based on March 2022, Curriculum Version 1 Module Title: -Draw and Interpret Drawing Module code: IND MAC1 M01 02 22 Nominal duration: 100Hour Prepared by: Ministry of Labour and Skill August, 2022 Addis Ababa, Ethiopia Table of Content Acknoledgment Introduction To The Module ....................................................................................................... 6 Unit One: Prepare For Drawing................................................................................................. 7 1.1. Introduction Drawing ................................................................................................ 8 1.2. Drawing Instruments............................................................................................... 11 1.3. Read And Interpreted Lines : .................................................................................. 19 1.4. Measurements And Scales ...................................................................................... 21 1.4.1. Drawing Standards .......................................................................................... 21 1.4.2. Scale (Ruler): ................................................................................................... 23 1.5. Lettering: ................................................................................................................. 25 Self Check-1 ................................................................................................................. 29 Operation Sheet-1.1.Peractice Using Drawing Instruments ........................................ 30 Operation Sheet-1.2. Scale ........................................................................................... 31 Operation Sheet-1.3: Template And Title Block ......................................................... 31 Lap Test-1 .................................................................................................................... 32 Lap Test-2 .................................................................................................................... 33 Lap Test 3 ..................................................................................................................... 33 Unit Two: Draw Simple Drawing ............................................................................................. 34 2.1. A Series Of Geometric Shapes ............................................................................... 35 2.1.1. Geometrical Construction Problems .............................................................. 35 2.1. A Few Basic Points For A Drawing ....................................................................... 43 Self Check-1 ................................................................................................................. 44 2.1.2. Operation Sheet 2.1: Construct A N Sides On A Straight Line ..................... 46 Lap Test-2.1 ................................................................................................................. 47 Unit Three: Construct Multi-View ........................................................................................... 48 3.1. Projection View ...................................................................................................... 49 3.1.1 Types Of Projection ......................................................................................... 50 3.1.2. Projection Words ............................................................................................. 52 3.1.3. Quadrant System ............................................................................................. 52 3.2. Sketching Multi View Drawings ............................................................................ 52 3.2.1. Width, Depth, And Height .............................................................................. 54 3.2.2. First-An

FAQs

What topics are included in Unit One for preparing drawing?

Unit One covers introduction to drawing, drawing instruments, reading and interpreting lines, measurements and scales (including drawing standards and ruler scale), and lettering.

How does the module train students to create multi-view drawings?

Unit Three focuses on projection views, types of projection and projection words, quadrant system, sketching multi-view drawings, first-angle and third-angle concepts, orthographic projection principles, and 3D pictorial drawing including view selection and line precedence.

What skills does Unit Four emphasize?

Unit Four emphasizes freehand sketching requirements and introduces dimensioning fundamentals to support accurate representation in sketches.

Oct 23, 2026

Upload by Bintang