Malibu Fender Hash Mark Decal Kit - PART NO. 23401196 - Installation Instruction Sheet

Sep 4, 2026

Upload by Gelato

Installation instructions for a Malibu fender hash mark decal kit, including kit contents, required tools, and a step-by-step procedure to apply the decals to the front fender. The instructions cover correct surface temperature, cleaning with solvent wipe, trimming and aligning the template, wetting the adhesive side, and pressing/using the squeegee sequence. Guidance is provided for premask removal, bubble handling with a needle, heat reactivation for unsealed areas, and a 72-hour high-pressure wash restriction after completion.

LanguageEnglish

CategoryPaper Templates

FormatPDF

Pages4

Reading Time2 min

AccessFree to download

Contents

Tools Required

Suggested Installation Procedure

| | | | | | | | | --- | --- | --- | --- | --- | --- | --- | | Malibu Fender Hash Mark Decal Kit
Contents Quantity
Decal-F/Fdr LH 1
Decal-F/Fdr RH 1
Solvent Wipe 2
Installation Instruction Sheet 1
Tools Required
• Lint-free cloth
• Hair Dryer
• Spray bottle that contains a wetting solution (2 drops of unscented liquid detergent mixed with 24 oz. of water)
• Plastic Squeegee
• Sewing Needle
• Masking Tape
• Scissors
Suggested Installation Procedure:
1. The body surface should be between 60°F and 90°F at the time of installation and for two hours after.
2. Thoroughly wash the front fender surface with warm soap and water.
3. Clean the surface with solvent wipe and remove any residue with a clean, lint-free cloth.
4. Using scissors, trim out the template and align and tape to the fender as shown below.
5.
6. Use the wetting solution to saturate the exposed adhesive side of the decal.
7. Align the front edge of the blue premask carrier to the rear edge of the template while aligning the top edge to the top edge of the fender and aligning to the lower edge to the wheel well opening.
8.
9. Carefully remove the premask at 180 degrees.
10. After premask removal, never use an uncovered squeegee to re-press a stripe into place. Wrap the squeegee with a towel or re-spray the surface with surfactant.
11. If bubbles are present after premask carrier removal, wrap a towel around the squeegee and carefully attempt to push the bubble to the side of the stripe. If the bubble cannot be moved, use a sewing needle to pierce the bubble and press the remaining solution from beneath the stripe.
12. For any areas that may have become unsealed, apply heat using a hair dryer and then use a towel to gently press the decal into place. Note: After a stripe installation has been completed, do not high pressure wash the vehicle for 72 hours. | | | | | | | |
Figure 1
-Arrows represent squeegee direction and sequence-RH symmetrically opposite |
Figure 2 | | | | | | | Malibu Front Fender Hash Mark Decal Kit IR 08DE16 | | PART NO. 23401196 | SHEET | 1 | OF | 4 | | |
French | | | | | | | | | | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | | | | | | | | | | | | | Trousse de bande autocollante oblique d'aile de Malibu
Contenu Quantité
Décalque-aile avant gauche 1
Décalque-aile avant droite 1
Tampon de solvant 2
Feuille d'instructions d'installation 1
Outils nécessaires
• Chiffon non pelucheux
• Séchoir
• Pulvérisateur contenant une solution mouillante (2 gouttes de détergent liquide inodore mélangée à 24 oz d'eau)
• Raclette en plastique
• Aiguille à coudre
• Ruban de masquage
• Ciseaux
Méthode de pose suggérée :
1. La température de surface de la carrosserie doit être comprise entre 60°F et 90°F au moment de l'installation et deux heures aprèsl'installation.
2. Bien nettoyer la surface de l'aile avant avec de l'eau chaude savonneuse.
3. Nettoyer la surface avec un tampon de solvant et enlever tout résidu avec un chiffon non pelucheux propre.
4.
5. Placer le décalque face vers le bas sur une surface plane et retirer lentement le papier protecteur (la surface adhésive sera alors exposée) .
6. Mouiller abondamment la surface adhésive exposée du décalque avec de la solution mouillante.
7. Aligner le bord avant du support de pré-masque bleu sur le bord arrière du gabarit tout en alignant le bord supérieur sur le bord supérieur del'aile et en l'alignant sur le bord inférieur du passage roue.
8. À l'aide d'une raclette en plastique, coller le décalque en place tout en exerçant fermement des mouvements chevauchants

9. Déposer soigneusement le prémasquage à 180 degrés.
10. Une fois le prémasque enlevé, ne jamais utiliser une raclette non couverte pour presser de nouveau la bande en place.
Envelopper la raclette dans une serviette ou pulvériser de n

FAQs

What surface temperature range is required before and after installation?

The body surface should be between 60°F and 90°F at the time of installation and for two hours after.

How should the decal adhesive be prepared before alignment?

Clean the surface with a solvent wipe and remove residue with a clean, lint-free cloth, then trim and align the template, and saturate the exposed adhesive side with the wetting solution.

What should be done if bubbles appear after removing the premask carrier?

Push the bubble carefully to the side; if it cannot be moved, pierce the bubble with a sewing needle and press the remaining solution from beneath the stripe.

Sep 4, 2026

Upload by Gelato