ISO/IEC 25001:2007 - Software engineering—Planning and management of software product Quality Requirements and Evaluation (SQuaRE)

Sep 12, 2026

ISO/IEC 25001:2007 specifies software engineering activities for planning and management within the SQuaRE framework. The standard defines scope and conformance expectations, provides key terms for evaluation activities, evaluation groups, evaluation technology, and techniques, and organizes evaluation management concepts. It also lays out requirements and recommendations for software quality requirements, covering management level activities and evaluation planning, including analysis and use of evaluation results, supported by an informative annex template and references.

LanguageEnglish

CategoryPresentations

FormatPDF

Pages11

Reading Time4 min

AccessFree to download

Contents

FOREWORD

INTRODUCTION

1 SCOPE

2 CONFORMANCE

3 NORMATIVE REFERENCES

4 TERMS AND DEFINITIONS

5 EVALUATION MANAGEMENT CONCEPTS

6 REQUIREMENTS AND RECOMMENDATIONS FOR SOFTWARE QUALITY REQUIREMENTS

Annex A (Informative)

Bibliography

INTERNATIONAL STANDARD ISO/IEC 25001 First edition 2007-02-01 Software engineering—Software product Quality Requirements and Evaluation (SQuaRE)—Planning and management Ingénierie du logiciel—Exigences de qualité et évaluation du produit logiciel (SQuaRE)—Planification et gestion iTeh STANDARD PREVIEW ( [standards.iteh.ai](standards.iteh.ai)) ISO/IEC 25001:2007 [https://standards.iteh.ai/catalog/standards/sist/acf4468a-4192-454e-ab89-](https://standards.iteh.ai/catalog/standards/sist/acf4468a-4192-454e-ab89-) ad543aab64b3/iso-iec-25001-2007 Reference number ISO/IEC 25001:2007(E) © ISO/IEC 2007 ISO/IEC 25001:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. iTeh STANDARD PREVIEW ( [standards.iteh.ai](standards.iteh.ai)) ISO/IEC 25001:2007 [https://standards.iteh.ai/catalog/standards/sist/acf4468a-4192-454e-ab89-](https://standards.iteh.ai/catalog/standards/sist/acf4468a-4192-454e-ab89-) ad543aab64b3/iso-iec-25001-2007 © ISO/IEC 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [copyright@iso.org](copyright@iso.org) [Web www.iso.org](Web www.iso.org)[ ](Web www.iso.org)Published in Switzerland ii © ISO/IEC 2007 – All rights reserved ISO/IEC 25001:2007(E) Contents FOREWORD ............................................................................................................................iv INTRODUCTION.....................................................................................................................v 1 SCOPE ................................................................................................................................1 2 CONFORMANCE ............................................................................................................1 3 NORMATIVE REFERENCES ........................................................................................2 4 TERMS AND DEFINITIONS .........................................................................................3 4.1 EVALUATION ACTIVITY ..................................................................................................3 4.2 EVALUATION GROUP .......................................................................................................3 4.3 EVALUATION TECHNOLOGY (TECHNOLOGY USED FOR EVALUATION) .............................3 4.4 TECHNIQUES ..................................................................................................................3 5 EVALUATION MANAGEMENT CONCEPTS ............................................................3 6 REQUIREMENTS AND RECOMMENDATIONS FOR SOFTWARE QUALITY REQUIREMENiTTS ECICAAINAITVUIN ..................................4 6.1 6.2 6.3 6.4 GENERALORGANISA.T..I.O...

FAQs

What does ISO/IEC 25001:2007 cover?

It covers planning and management activities for software product quality requirements and evaluation within the SQuaRE framework. It includes scope, conformance, key evaluation concepts, and requirements/recommendations for quality requirements and evaluation management.

Which evaluation-related terms are defined?

The standard defines terms such as evaluation activity, evaluation group, evaluation technology used for evaluation, and techniques. These terms support consistent understanding of evaluation planning and management.

Does ISO/IEC 25001:2007 include informative supporting material?

Yes. It references an informative annex (Annex A) providing a template, and it also includes a bibliography for related materials.

Sep 12, 2026

Upload by William