EXHIBIT X-1A TEMPLATE FOR SCHEDULE OF APPROVED WIRELESS FACILITIES - RF compliance and installation document requirements

Sep 25, 2026

Template for completing the schedule of an approved wireless facility design under Exhibit X-1A. Specifies selectable attachment types and required attachment details, including standard concrete light pole characteristics, antenna system size limits, concealment requirements, and included engineering drawing and photo submittals. Provides general notes on approximate dimensions/specifications and installation assumptions, plus RF compliance information tied to existing XRF information.

LanguageEnglish

CategoryForms

FormatPDF

Pages25

Reading Time9 min

AccessFree to download

Facility schedule requirements

Attachment types and required details

Included documents

RF compliance information

General notes

Standard concrete pole elevation exhibits

# EXHIBIT X-1ATEMPLATE FORSCHEDULE OF APPROVED WIRELESS FACILITIES (To be completed for each Approved Wireless Facility design) | Facility
Number | X-1A Standard Concrete Light Pole Antenna System | | --- | --- | | Attachment
Types
(check all that
apply and
provide detail
below) | _X__Replacement City Pole(streetlight)
x__Replacement City Property Pole(streetlight)
x_Attach to existing City Pole(streetlight)
_x_Attach to existing City Property Pole(streetlight)
Attach to existing City Pole (traffic signal)
Attach to existing City Property Pole(traffic signal)
Attach to existing City Pole (street furniture)
Attach to existing City Property Pole(street furniture)
Attach to Non-City Pole | | Attachment
Type Detail | Standard concrete light pole or similar(existing or replacement) | | Physical
Description | Antenna System(no more than 42”diameter and no more than 30”height)mounted to
exterior of pole and painted to match pole.Antenna system can be installed above or
below LED light fixture.Antenna system can be installed with previously approved
Exhibit Xl antenna or as stand-alone system.Radio equipment,power and fiber
equipment concealed within stealth expanded base,not to exceed 2.5'diameter and will
be painted to match exterior pole.
Overall height of replacement pole not to exceed 20%of existing pole height(not
including antenna) | | Concealment | Radio equipment,power and fiber equipment concealed within stealth expanded base,
not to exceed 2.5'in diameter and 4’8”in height.A maximum of an additional 2'
above enclosure will be used to add decorative tapering. | | Included
Documents | The following documents:
A.For each Attachment Type listed or checked above,an engineering drawing of replacement pole
or existing pole with attached equipment.The drawing must show the location on the pole where
each component of the Wireless Facility is attached or enclosed.Drawings should depict any
underground portion of the typical installation for thatAttachment Type.
B.Photo showing an example of each Attachment Type listed or checked above.
C.Photo mockup of each Attachment Type listed or checked above showing the appearance after
the Approved Wireless Facility is installed.
Engineering drawings and photo attachments should reflect the dimensions and characteristics ofa
representative actual City Pole or City Property Pole of the type to which the Approved Wireless Facility
design applies rather than generic examples.Where there is considerable variation among City Poles/City
Property Poles of a particular type(e.g.traffic signals),drawings can show a typical installation,provided
that equipment volumes and attachment locations will not vary significantly from one installation to the
next in ways that are material to the City's interests. | | RF
Compliance
Information | □Facility conforms to information already on file XRF information attached | ## GENERAL NOTES: 1.ALL DISTANCES,DIMENSIONS,LOCATIONS,AND EQUIPMENTDESIGNATIONS AND SPECIFICATIONS ARE APPROXIMATE. 2.ALL MATERIALS WILL RESEMBLE CURRENTLY EXISTING MATERIALSBE REPLACED WITH A NEW POLE WITH A ## STANDARD CONCRETE POLE ELEVATION -EXHIBIT X-1A SCALE:1”=5’ | REVISIONS | | | | | --- | --- | --- | --- | | REV | DATE | DESCRIPTION | BY | | 5 | 08/28/18 | FOR SUBMITTAL | JEB | | | | | | | | | | | | | | | | | | | | | | | | | | SK-1A verizon 118 FLANDERS ROAD THIRD FLOOR WESTBOROUGH,MA 01581 GENERAL NOTES: NEW TECHNOLOGY NOTE: THE MAXIMUM ANTENNA SYSTEM SHOWN HEREINMAY BE INSTALLED IN CONJUNCTION WITH THE1.ALL DISTANCES,DIMENSIONS,LOCATIONS,AND EQUIPMENTPREVIOUSLY APPROVED EXHIBIT X ANTENNA ORDESIGNATIONS AND SPECIFICATIONS ARE APPROXIMATE.AS A STANDALONE CONFIGURATION.2.ALL MATERIALS WIL

FAQs

What information must be completed for Exhibit X-1A?

Complete the schedule for each Approved Wireless Facility design by selecting attachment types, providing attachment type details, describing the antenna system and concealment approach, and ensuring the included documents are provided.

What are the key antenna system and concealment limits stated in the template?

The antenna system must not exceed the stated diameter and height, and the stealth expanded base concealment is limited by diameter and enclosure height, with an additional portion allowed for decorative tapering.

Which documents are required in the included documents section?

For each selected attachment type, provide engineering drawings showing component attachment/enclosure locations and typical underground portions, plus photos showing each attachment type and a photo mockup showing appearance after installation.

Sep 25, 2026

Upload by Alex Sinclair