Vandal Resistant Laminar Outlet with Antimicrobial by Agion® 1.5 GPM (5 .7 L/min) - Installation and Setup Instructions

Oct 22, 2026

Upload by Tirek

Installation and setup instructions for a vandal-resistant laminar outlet system with antimicrobial protection by Agion®. The sheet lists compatible outlet and accessory components, including aerators, flow-control parts, deck plates, hoses, solenoid valve fittings, and power options (battery version or 24 VAC converter/hardwire). It specifies disinfection-cycle and system-pressure guidance, plus step-by-step faucet mounting, battery box installation, flushing, water-supply connections, and power-up procedures with safety warnings and torque/sealant notes.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages8

Reading Time20 min

AccessFree to download

Installation and Setup Instructions for Surface Mount Housing: Control Box #0

Step 1. Faucet Installation

Step 2. Battery Box Installation

Step 3. Flush System

Step 4. Connect Water Supply

Step 5. Power Up

208356 208356 208356 208356 060638A Vandal Resistant Laminar Outlet with Antimicrobial by Agion® 1.5 GPM (5 .7 L/min) 060640A Vandal Resistant Flow Control Aerator and Wrench 1.5 GPM (5 .7 L/min) 061203A Vandal Resistant Laminar Outlet with Wrench 0.5 GPM (1 .9 L/min) 061176A Vandal Resistant Laminar Outlet with Wrench 1.0 GPM (3 .8 L/min) 061104A Vandal Resistant Flow Control Non-Aerating Spray Outlet with Wrench 0.35 USGPM (1 .3 L/min) RP31704-Optional Vandal Resistant Spray Outlet with Wrench 0.5 GPM (1 .9 L/min) 060566A-Optional Vandal Resistant Spray Outlet with Wrench 1.0 GPM (3 .8 L/min) 060765A Wrench 060564A Single Hole Deck Gasket (6/pkg) Accessories 060683A 24 VAC/6 .4 VDC Converter 061256A 36” Cable Extension | 590T | | --- | | Write purchase model number here for future reference | NOTE: Control Box \#0 and \#1 are designed for routine 171° F (77°C) disinfection cycles up to 30 minutes. Control Box \#8 is not recommended for high temperature disinfection cycles as the thermostatic mixing valve limits the higher temperature flow output. NOTE: For optimum performance of this product, we recommend a system pressure between 20 and 80 PSI static. This product will operate up to a maximum of 125 PSI static per ANSI and CSA requirements. However, we do not recommend pressure above 80 PSI. Thermal expansion or leaking pressure reducing valves may require the use of expansion tanks or relief valves to ensure your system never exceeds its maximum intended pressure setting. RP6087 Nut and Washer RP30523 Braided Hose 063127A Solenoid Valve with 3/8” Compression Connectors | OPTION LIST | | --- | |
060681A
Battery Holder | | TRANSFORMERS 060704A
Transformer 110 to 24 VAC 20VA up to 5 Electronic Valves
060771A
Transformer 110 to 24 VAC 40VA up to 10 Electronic Valves
060772A
Transformer 110 to 24 VAC 100VA up to 25 Electronic Valves | | DECK PLATES
060546A
4” Deck Plate & Hold-Down Pkg
060547A
8” Deck Plate & Hold-Down Pkg | 208356 208356 208356 208356 060905A Cover Gasket 060906A Surface Mount Housing 061252A ~~ ~~ Dual Driver Board Masco H 2Optics & Proximity 063128A Battery Box Assembly less driver board and battery holder 063127A Solenoid Valve with 3/8”Compression Connectors 060908A Solenoid Holder 060909A Screen Assembly 063131A 3/8” Comp Connect Nut and Ferrile 063131A 3/8” x 3/8”Compression Connector, Nut and Ferrule RP6092 060546A 4” Deck Plate and Hold-Down Package 060547A 8” Deck Plate and Hold-Down Package Nut and Washer Fig. 1 PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, [etc. as](etc. as)[ ](etc. as)[items relating to ongoing maintenance suggestions and procedures are included.](items relating to ongoing maintenance suggestions and procedures are included.) [ww w . spec select . co m](ww w . spec select . co m) Page 1 208356 Rev. C Installation should be in accordance with local plumbing and electrical codes. FLUSH ALL PIPES THOROUGHLY BEFORE INSTALLATION. INSTALLATION AND SET UP INSTRUCTIONS FOR SURFACE MOUNT HOUSING: CONTROL BOX \#0 STEP 1. FAUCET INSTALLATION | Connect 20” braided hose to spout inlet. Clean deck/sink surface where faucet will be mounted. Mount faucet to sink using nut(s) and washer(s) provided. Installation of the single hole deck gasket (060564A) between the turret base and mounting surface is the recommended assembly practice. Ensure that gasket is sitting flat on the deck and the turret is centered on the gasket. Use the same procedure for installation of optional 4”or 8” deck plate package (060546A or 060547A) . Mount the faucet to the sink using nut(s) and washer(s) provided. Do not overtighten the nut (RP6087) or reposition the turret once installed, otherwise damage to the gasket may result. Cutting or trimming of the gasket is not recommended. NOTE: If the gasket is trimmed

FAQs

What is the recommended practice for mounting the faucet on the deck surface?

Mount the faucet using the provided nuts and washers, and install the single-hole deck gasket (060564A) between the turret base and mounting surface. Keep the gasket flat and center the turret; avoid overtightening or repositioning after installation to prevent gasket damage.

How should the system be flushed before connecting the solenoid inlet?

Assemble the specified components (Fig. 3) and run water for 1 minute, then shut off the water supply. Attach the aerator and do not connect the supply to the solenoid inlet until the line is flushed directly out through the spout.

What power options does the sheet provide and what are key cautions?

Use either the battery version (install four Alkaline C batteries in the battery holder) or a hardwire version using a CSA/UL-approved Class 2 transformer or equivalent (do not install the transformer inside the control box). Do not use a 9V battery, and connect wiring carefully without damaging driver-board components.

Oct 22, 2026

Upload by Tirek