UEE33020 Certificate III in Electrical Fitting - Version 1 - Course overview and 2026 delivery details

Sep 15, 2026

Uploaded by Maeve

UEE33020 Certificate III in Electrical Fitting outlines the competencies to manufacture, fit, assemble, erect, operate, test, fault find, alter and repair electrical equipment, including associated wiring work between electrical components within plants or machinery. Eligibility focuses on an NT Apprentice Training Licence (Red Card) and a Language, Literacy, Numeracy and Digital Literacy evaluation. The 2026 delivery includes face-to-face and simulated workplace study in Casuarina and Alice Springs over a four-year schedule, with assessment methods and pathways such as RPL and credit transfer.

LanguageEnglish

CategoryExam

FormatPDF

Pages4

Reading Time10 min

AccessFree to download

UEE33020 Certificate III in Electrical Fitting

Qualification description and scope

Eligibility/entry requirements

Delivery details

Fees

Assessment

Recognition of prior learning (RPL)

Credit transfer (CT)

Resources

UEE33020 Certificate III in Electrical Fitting DESCRIPTION This qualification provides competencies to manufacture, fit, assemble, erect, operate, test, fault find, alter and repair electrical equipment and includes electrical wiring work only if that work is associated with assembling, maintaining, terminating or altering the wiring between electrical components within a plant or machinery. An electrical fitter is not authorised to install any electrical wiring systems within an electrical installation as prescribed by definitions contained in AS/NZS 3000 Electrical installations (known as the Australian/New Zealand Wiring Rules) . Electrical equipment means any appliance, article, accessory, wire, fitting, cable, conduit or apparatus that generates, uses, conveys or controls (or that is intended to generate, use, convey or control) electricity above extra-low voltage (ELV) . The skills and knowledge described in this qualification may require a licence or permit to practice in the workplace where work is carried out on electrical installations which are designed to operate at voltages greater than 50 volt (V) alternating current (a. c. ) or 120 V direct current (d. c. ) . Competency development activities in this qualification may be subject to regulations directly related to licensing. Where a licence or permit to practice is not held, a relevant contract of training through an Australian Apprenticeship, may be required. Licensing, legislative and regulatory requirements that apply to this qualification can vary between states and territories. Some jurisdictions require that the qualification is completed as an apprenticeship to obtain an Electrical Occupational License. Relevant information must be sourced prior to commencing the qualification. Where required for Licencing, the certification documentation issued must indicate if the qualification was completed as an apprenticeship or Trades Recognition Australia (TRA) pathway. ELIGIBILITY/ENTRY REQUIREMENTS A Language, Literacy, Numeracy and Digital Literacy (LLND) evaluation helps identify any areas where you may need additional support to help you achieve your goals. To gain entry into the UEE33020 Certificate III in Electrical Fitting, candidates are required to: • To be an Apprentice who has entered a Training Contract with their employer and Australian Apprenticeship Support Network NT. • Hold an NT Apprentice Training Licence (Red Card) -[https://electricallicensing.nt.gov.au/home](https://electricallicensing.nt.gov.au/home). DELIVERY DETAILS | Location(s) | Casuarina, Alice Springs | | --- | --- | | Duration * | 4 years
Block delivery 3 to 4 x 2-week blocks each year over 4 years | | Study mode ^^ | Face-to-face, Simulated workplace, Industry practice | | Dates ^ | Start and end dates:
January 12, 2026 – December 11, 2026 | Page 1 of 4 UEE33020 Certificate III in Electrical Fitting 2026 – Version 1 CRICOS Provider No. 00300K (NT/VIC) | 03286A (NSW) | RTO Provider No. 0373 | ABN 54 093 513 649 | | Apprentice will receive an individual call-up notification letter. | | --- | --- | | Attendance | Face to Face as required. To be notified by Lecturer as required. | * Duration may vary depending on how long a student takes to reach the required competency level. ^ Course timetable will be provided on application for the course. ^^Information relating to study modes can be found in the 2026 TAFE Student Guide FEES | Fee Type | 2026 Course Fees | | --- | --- | | NT Government Supported* | $3,965.50- $4,404.40 | | Full Fee | $14,224.30- $15,798.64 | *This course is supported by the NT Government for domestic eligible students who are NT residents. A limited number of NT Government supported places are available, so secure your place now. Fees shown are indicative and subject to change annually. Actual course fees may vary depending on the units chosen. For International non-student visa-holders; study eligibility needs to

FAQs

What work does UEE33020 Certificate III in Electrical Fitting cover?

It covers manufacturing, fitting, assembling, erecting, operating, testing, fault finding, altering and repairing electrical equipment, including wiring work only when associated with assembling, maintaining, terminating or altering wiring between electrical components.

What are the entry requirements for this qualification?

Candidates must be an Apprentice with a Training Contract, hold an NT Apprentice Training Licence (Red Card), and complete a Language, Literacy, Numeracy and Digital Literacy (LLND) evaluation to identify support needs.

How is the course delivered in 2026?

Delivery is face-to-face with simulated workplace and industry practice. It runs from January 12, 2026 to December 11, 2026, with a four-year duration and block delivery of 3 to 4 two-week blocks each year.

Sep 15, 2026

Uploaded by Maeve