TM 9-1005-206-14&P-1 - Change No. 1 - Operator’s and Maintenance Manual Updates

Oct 24, 2026

Upload by Connor

Operator’s, Organizational, Direct Support, and General Support Maintenance Manual including Repair Parts and Special Tools List for specified revolvers. The text emphasizes mandatory safety precautions, including verifying the weapon is unloaded, preventing live ammunition near the work area, and handling cleaning solvents and skin protection during disassembly and cleaning. It also provides inspection cautions related to barrel obstructions, guidance to stop firing when anomalies occur, and references to related first-aid and ammunition information. A change notice outlines revised maintenance procedures and required page replacements.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages163

Reading Time6 h 51 min

AccessFree to download

WARNING

Safety precautions (General)

FIRST AID

AMMUNITION

CHANGE NO. 1

Remove pages

Insert pages

TM 9-1005-206-14&P-1 TECHNICAL MANUAL OPERATOR’S, ORGANIZATIONAL, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST FOR REVOLVER, CALIBER .38 SPECIAL: SMITH AND WESSON MILITARY AND POLICE, M10 ROUND BUTT, 4-INCH BARREL (1005-00-937-5839) ROUND BUTT, 2-INCH BARREL (1005-00-937-5840) SQUARE BUTT, 4-INCH BARREL (1005-00-214-0934) REVOLVER, CALIBER .38 SPECIAL: RUGER SERVICE SIX, 4-INCH BARREL, M108 SQUARE BUTT W/O LANYARD LOOP (1005-01-040-8989) SQUARE BUTT W/LANYARD LOOP (1005-01-040-8990) ROUND BUTT, W/LANYARD LOOP (1005-01-094-7045) HEADQUARTERS, DEPARTMENT OF THE ARMY WARNING Make sure that each weapon is unloaded prior to inspection. Avoid having live ammunition in the vicinity of the work area. Dry cleaning solvent is flammable and toxic and should be used in a well-ventilated area. The use of rubber gloves is necessary to protect the skin when cleaning revolver parts. Avoid skin contact with carbon removing compounds. Beware of obstructions in the barrel. Inspect the barrel for obstructions before firing. Objects in the barrel such as mud, snow, twigs, or heavy amounts of CLP can cause obstructions resulting in a bulged or burst barrel. If, when firing, a weak or peculiar report is heard, stop firing at once to inspect the barrel for a stuck bullet. SAFETY PRECAUTIONS (General) The following general safety precautions are also applicable. There are many safety rules, but those found below are basic and should be observed rigidly. The revolver must always be checked for live ammunition when picked up, drawn from the holster, handed to, or accepted from, another person. The revolver should always be holstered except when drawn for a definite purpose. Never point the revolver at anything that you do not intend to shoot. Do not cock the revolver unless you intend to shoot it. Do not even insert the finger in the trigger guard until you are ready to fire. Dry-snapping, even with dummy cartridges, should be discouraged unless it is performed on a regular target range or at a known target. When the revolver is out of the hoister and held in a ready position, be absolutely certain that it is not pointing at any part of yourself or at other persons who are near you. FIRST AID For additional first aid data, see FM 21-11. AMMUNITION TM 9-1300-206 provides information for revolver ammunition. TM 9-1005-206-14&P-1 C1 CHANGE NO. 1 HEADQUARTERS DEPARTMENT OF THE ARMY Washington, DC 3 December 1986 Operator’s , Organizational , Direct Support , and General Support Maintenance Manual Including Repair Parts And Special Tools List fo r REVOLVER, CALIBER .38 SPECIAL: SMITH AND WESSON , MILITARY AND POLICE, M10 ROUND BUTT, 4-INCH BARREL (1005-00-937-5839) ROUND BUTT, 2-INCH BARREL (1005-00-937-5840) SQUARE BUTT, 4-INCH BARREL (1005-00-214-0934) AND REVOLVER, CALIBER .38 SPECIAL : RUGER SERVICE SIX, 4-INCH BARREL, M108 SQUARE BUTT, W/O LANYARD LOOP (1005-01-040-8989) SQUARE BUTT, W/LANYARD LOOP (1005-01-040-8990) ROUND BUTT, W/LANYARD LOO P (1005-01-094-7045) TM 9-1005-206-14&P-1, 28 August 1985, is changed as follows : 1. Remove old pages and insert new pages as indicated below. 2. New or changed material is indicated by a vertical bar in the outer margin of the page . 3. This change contains revised procedures for maintenance of revolver assembly. REMOVE PAGES 6-7 thru 6-10 6-33 and 6-34 C8-1 and C9-1 C13-1 and C14-1 C16-1 I-3 and I-4 I -5 INSERT PAGES 6-7 thru 6-10 . 1/(6-10 . 2 blank ) 6-33 and 6-34 C8-1 and C9-1 C13-1 and C14-1 C16-1 I-3 and I-4 I-5 File this change sheet in back of the publication for reference purposes . By Order of the Secretary of the Army: JOHN A. WICKHAM, JR. General, United States Army Chief of Staff Official: R. L. DILWORTH Brigadier General, United States Army The Adjutant General DISTRIBUTION: To be distribute

FAQs

What must be done before inspecting the weapon?

Ensure each weapon is unloaded prior to inspection, and avoid live ammunition in the work area.

What should be checked in the barrel if a weak or peculiar report occurs?

Stop firing immediately and inspect the barrel for a stuck bullet or obstructions such as mud, snow, twigs, or excessive CLP.

What does Change No. 1 require for the manual pages?

Remove the listed old pages and insert the corresponding new or revised pages, then file the change sheet in the back of the publication for reference.

Oct 24, 2026

Upload by Connor