Structural Standard Drawings - Drawing List of SEB Typical Details (1) - General Notes - Reinforcement and Lap/Bend Requirements

Oct 23, 2026

Upload by Asher

Comprehensive structural standard drawing set listing SEB typical detailing requirements for reinforced concrete works, covering typical detailing drawings SD/001 to SD/026 with general applicability and precedence rules. General notes define common anchorage, laps, bends, trimming bars, spacers and stirrups, including abbreviation standards, reinforcement notation (plain vs ribbed bars to CS2:2012), unit conventions in millimetres, and dimensional precedence between general and contract drawings. Includes bar cranking, standard hooks and bends with minimum internal radius guidance, plus lap and anchorage length tables by bar size and concrete grade.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages36

Reading Time1 h 31 min

AccessFree to download

Drawing list of SEB typical details (1)

General notes

Cranking of bars, standard hooks and bends

| DRAWING LIST OF SEB TYPICAL DETAILS(1) | | | | | | | --- | --- | --- | --- | --- | --- | | DRAWING No. | DRAWING TITLE | | | | | | SD/001G | DRAWING LIST OF SEB TYPICAL DETALS(1) | | | | | | SD/002C | GENERAL NOTES | | | | | | SD/003B | CRANKING OF BARS,STANDARD HOOKS AND BENDS | | | | | | SD/004B | STEEL REINFORCEMENT ANCHORAGE AND LAP LENGTH REQUIREMENT | | | | | | SD/005C | TYPICAL DETAL OF SPACER BARS AND STIRRUPS AT BEAMS | | | | | | SD/006D | TYPICAL DETAIL OF TORSION STRRUPS AND COLUMN BINDERS | | | | | | SD/007 | TYPICAL WALL JUNCTION DETALS | | | | | | SD/008 | TYPICAL DETAIL OF BRICK OR R.C.PARTTTION WALL AND WALL BASE | | | | | | SD/009 | TYPICAL DETAL OF R.C.STRUCTURAL WALL | | | | | | SD/010 | TYPICAL DETAIL OF TRIMMING BARS FOR WALL OPENING | | | | | | SD/011 | TYPICAL DETAIL OF TRIMMING BARS FOR PERMANENT SLAB OPENING | | | | | | SD/012 | TYPICAL DETAIL OF TRIMMING BARS FOR TEMPORARY SLAB OPENING | | | | | | SD/013 | TYPICAL DETAIL FOR TEMPORARY PIPE DUCT OPENING IN SLAB | | | | | | SD/014 | (NOT USED) | | | | | | SD/015B | ANCHORAGE AND LAPPING ARRANGEMENT OF BEAM LONGTUDINAL BARS | | | | | | SD/016 | TYPICAL DETAIL OF BEAM AND BEAM t'JUNCTION | | | | | | SD/017C | TYPICAL DETAIL OF COLUMNS | | | | | | SD/018A | TYPICAL DETAIL OF ROOF BEAM &EXTERIOR COLUMN JUNCTION | | | | | | SD/019B | TYPICAL DETAIL OF 100 THICK GROUND SLAB ON GRADE | | | | | | SD/020C | TYPICAL DETAIL OF 150 THICK GROUND SLAB ON GRADE | | | | | | SD/021C | TYPICAL DETAIL OF 200 THICK GROUND SLAB ON GRADE | | | | | | SD/022A | (10F 5)
TYPICAL DETAIL OF EXTERNAL DRNEWAY AND CARPARK GROUND SLAB ON GRADE | | | | | | SD/023A | (2 OF 5)
TYPICAL DETAIL OF EXTERNAL DRVEWAY AND CARPARK GROUND SLAB ON GRADE | | | | | | SD/024A | (3 OF 5)
TYPICAL DETAIL OF EXTERNAL DRNEWAY AND CARPARK GROUND SLAB ON GRADE | | | | | | SD/025A | (4 OF 5)
TYPICAL DETAIL OF EXTERNAL DRIVEWAY AND CARPARK GROUND SLAB ON GRADE | | | | | | SD/026B | TYPICAL DETAIL OF EXTERNAL DRNEWAY AND CARPARK GROUND SLAB ON GRADE
(5 OF 5) | | | | | | | | | | | | | drawing itle
DRAWING LIST OF
SEB TYPICAL DETAILS(1) | | date
checked
CSE/1 LS.LAU
JUNE,2021
C | drawing no.
SD/001 | rev.
G | scale
N.T.S. | | | | date
approved
AD(SE)K.L.TSE
JUNE,2021
WM | STRU.ENGG.BRANCH
ARCH.SERMCES DEPT. | | | # GENERAL NOTES: 1.TYPICAL DETAILS DRAWINGS SD/001 TO SD/026(FIG.1 TO 16 NCLUSIVE)AND MH/01 TOMH/11 INDICATE THE TYPICAL DETAILING REQUIREMENTS,e.g.ANCHORAGE,LAP,BEND,TRIMMING BARS,SPACER,ETC.,AND THE TYPICAL DETAILS OF DIFFERENT R.C.ELEMENTSGENERALLY ADOPTED IN R.C.WORKS.THEY SHALL NOT BE TAKEN AS REPRESENTING THECOMPLEXITY OF R.C.DETAILS FOR THE CONTRACT.SEPARATE R.C.DETAILS DRAWINGS ARE TOBE ISSUED FOR THE CONTRACT.IN CASE DIFFERENT R.C.DETAILS ARE SHOWN,THE DETAILSSHOWN ON R.C.DETAILS DRAWINGS SHALL TAKE PRECEDENCE. 2.ABBREVIATIONS:- a)GENERAL: DIA DIAMETER VERT VERTICAL HOR HORIZONTAL TYP TYPICAL b)RELATING TO REINFORCEMENT: ASAREA OF STEELB1BOTTOM LAYER OF BOTTOM REINFORCEMENTB2SECOND LAYER OF BOTTOM REINFORCEMENTT1TOP LAYER OF TOP REINFORCEMENTT2SECOND LAYER OF TOP REINFORCEMENTEFBARS IN EACH FACENFBARS IN NEAR FACE OF WALLFFBARS IN FAR FACE OF WALLBWBOTH WAYSLVLENGTH VARIESDSDOUBLE STIRRUPSTSTRIPLE STIRRUPSALTPLACED ALTERNATELYSTGDSTAGGEREDCALCOMPRESSION ANCHORAGE LENGTHCLLCOMPRESSION LAP LENGTHTALTENSION ANCHORAGE LENGTHTLLTENSION LAP LENGTH b BREADTH OF BEAM OR WALL OR COLUMNhDEPTH OF BEAM OR COLUMN OR WALL THICKNESSSPAN OF BEAM OR SLABØDIAMETER L 3.TYPE OF BEAM STIRRUPS AND COLUMN BINDERS ARE SHOWN ONTYPICAL DETAIL DRAWING Nos.SD/005 AND SD/006 RESPECTIVELY. e.g.T10-101(A),102(B)-200 DS 4.ALL DIMENSIONS SHOWN ARE IN MILL

FAQs

What do the SD/001 to SD/026 drawings represent in these notes?

They provide typical detailing requirements for reinforced concrete works, including anchorage, lap, bend, trimming bars, spacers, and other generally adopted typical details.

If different R.C. details are shown on contract drawings, which ones take precedence?

The details shown on the R.C. details drawings take precedence over the typical detailing drawings.

What information is included in the general notes section besides drawing coverage?

The general notes include abbreviation definitions, reinforcement notation rules for CS2:2012 (plain vs ribbed bars), dimensional units in millimetres, and requirements for beam stirrups and column binders referencing specific drawings.

Oct 23, 2026

Upload by Asher