StoQuik® Finish System for Insulated Concrete Forms (ICF) - Detail Booklet - Series 17.xx - Components 17.01

Oct 28, 2026

Upload by lilac

StoQuik® Finish System for Insulated Concrete Forms (ICF) is a decorative, protective direct-applied, above-grade acrylic-based textured finish system installed over ASTM C 578 Type I, II, or IV compliant molded EPS insulation wall forms. The system supports both residential and commercial wall construction, combining high-performance Sto finish layers with primer and base coat components. The booklet specifies components, materials, curing requirements, and installation cautions, including guidance for embedded non-metallic form ties and conditions when alternative assemblies are used.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages9

Reading Time23 min

AccessFree to download

Details

Components

Components: High Impact Resistance

Features

Interior Foundation Projections

Below Grade Components

Residential Window Sill

Finished Opening Sill

StoQuik® Finish System for ICF Insulated Concrete Forms Detail Booklet Series 17.xx | November 2022 Facades Direct Applied Finish Systems (DEFS) StoQuik® Finish System for Insulated Concrete Forms (ICF) is a decorative and protective direct applied, above grade, acrylic based textured ﬁnish system over ASTM C 578 Type I, II, or IV compliant molded EPS insulation wall forms. Sto’s high performance ﬁnishes provide a handsome aesthetic and a durable exterior skin. StoQuik® Finish System for Insulated Concrete Forms can be used in residential or commercial wall construction. StoQuik® Finish Systems for Insulated Concrete Forms Table of Contents Details Components ........................................................................................................................................................................ 17.01 Components: High Impact Resistance .................................................................................................................................... 17.02 Features ................................................................................................................................................................................ 17.06 Interior Foundation Projections .............................................................................................................................................. 17.10 Below Grade Components ..................................................................................................................................................... 17.11 Residential Window Sill ......................................................................................................................................................... 17.23 Finished Opening Sill ............................................................................................................................................................. 17.25 ATTENTION The ﬁnal design of any project is the sole responsibility of the Design Professional, with considerations for compliance with local building and design codes and requirements. Sto Corp. accepts no liability for design, engineering, or workmanship of any project. The information provided herein is in addition to other technical data provided by Sto Corp. (System Bulletin, Speciﬁcation, Guide Details, etc) . For more information, please [visit www.stocorp.com](visit www.stocorp.com) Sto Corp. 3800 Camp Creek Pkwy. SWBldg. 1400 • Suite 120 Atlanta, GA 30331 Tel: (800) 221-2397 Fax: (404) 346-3119 [http://www.stocorp.com](http://www.stocorp.com)[ ](http://www.stocorp.com)[helpdesk.stocorp.com](helpdesk.stocorp.com) ® StoQuik® Finish System for Insulated Concrete Forms (ICF) Components Detail No.: 17.01 Date: November 2022 |

Molded EPS Insulation Walls

ICF Form
Non-Metallic Form Ties imbedded into EPS walls
Vertical and Horizontal Steel Surface Markings Reinforcing Bars
Identifying tie locations

Completed Wall Components | | --- | |

Sto Textured Finish

StoPrimer

Poured Concrete

Reinforcing Bar
Surface Markings
Identifying tie locations

Sto Base Coat
with Sto Mesh embedded
| Notes: 1. Refer to System Speciﬁcations and System Bulletin for more information and design guidance on wall assembly components. 2. Forms suitable for direct application coatings have imbedded, non-metallic form ties positioned a minimum 1/2”(13 mm) from the outer surface. 3. The forms are molded 1.5 pcf, Expanded Polystyrene insulation (EPS) 4. Rasping the foam surface to provide a level surface for coatings shall not expose the form ties. 5. ICFs that differ from the above may be completed by adding: a) 1”(25 mm) EPS insulation and EIFS coatings b) Metal Lath and StoPowerwall Stucco, Sto Primer and Sto Finish. 6. Concrete s

FAQs

What substrate is the StoQuik® finish system applied over?

It is a direct-applied acrylic based textured finish system over ASTM C 578 Type I, II, or IV compliant molded EPS insulation wall forms.

What curing time is required before applying Sto coating materials?

Concrete shall be allowed to cure for a minimum of 28 days prior to application of Sto coating materials.

How far should embedded non-metallic form ties be positioned from the outer surface?

Embedded, non-metallic form ties must be positioned a minimum of 1/2 in (13 mm) from the outer surface for forms suitable for direct application coatings.

Oct 28, 2026

Upload by lilac