Smart Doorbell - ECDB2K Fort Battery Powered 4MP IP64 WiFi Doorbell w/ Chime - Quick Start Guide

Oct 25, 2026

Upload by Bulrr

Quick Start Guide for the ECDB2K Fort battery-powered 4MP IP64 WiFi doorbell with RF battery powered chime. Provides general safety and health guidance, installation options including AC connection (12–24V AC) with shock-risk precautions, and LED light mode status indicators. Covers app setup using ClickSmart+ (WiFi entry, QR scan, device connection), chime pairing, changing ringtones, resetting the device, and key usage requirements like 2.4GHz WiFi and charging time.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages8

Reading Time20 min

AccessFree to download

General Information

Smart Doorbell Contents

Product Description

Health & Safety

Preparation for Use

Overview

LED Light Modes

Installation

Mounting and AC Adapter Wiring

Indoor Chime Unit

Changing the Ringtone

Pairing

App Pairing

Resetting the Device

Guidance

Quick Start Guide General Information Read the instructions before commencing installation. The user is to retain the instructions for future reference. Before commencing electrical work, ensure the supply of the system has been safely isolated with all appropriate steps taken, if you are unsure please consult a competent electrician • Smart Doorbell • Non-replaceable rechargeable batteries • Mounting pack • USB-C Cable • 8GB Micro SD Card • RF Battery Powered Chime • 4MP Image Sensor • PIR Sensor • 2.4GHz WiFi Product Description • ECDB2K Fort Battery Powered 4MP IP64 WiFi Doorbell w/ Chime [https://www.espuk.com/technical-specification](https://www.espuk.com/technical-specification) The latest product manuals and software is available online: Health & Safety This unit must be installed by a suitably qualified person. Please ensure that all installations comply with the current IEE regulations. For reasons of space and clarity the diagrams have been simplified. The product is not user serviceable. Do not dismantle this product. Due to our policy of continuous product improvement and development, the specifications in this guide may be subject to change without prior notice. Preparation for use Ensure that the smart phone is connected to the same Wi-Fi network that you Would like to attach the device to. Ensure that you have a mobile device running iOS 8 or higher, or Android 4.1x or higher, and a 2.4 GHz Wi-Fi connection. Download the ClickSmart+ App on your mobile device from the App Store or Google Play. Sign in to Register following the instructions on the ClickSmart+ App. Overview MIC Lens IR Sensor PIR Speaker LED Indicator Doorbell button Screw hole LED Light modes: • Power up: Red flashing • WiFi Pairing mode: Triple beep, blue rapid flashing • WiFi connected: No bleep, blue solid light • Incoming Call: Doorbell rings • Power off: Triple beep • Wake up: Solid blue indicator • Wake up, WiFi off: Solid blue for 2 seconds, then rapidly flash • Sleep mode: No indicators • Device on, charging: Blue flashing when charging, off when charged • Device off, charging: Blue constantly on Installation Standard Bracket Angled Bracket 1 Mount by Screw 2 Insert the doorbell 3 Tighten securing screw UP 2 3 1 Using an AC Adapter The ECDB2K supports AC connection which must be 12 or 24V AC. Ensure to test your wiring to make sure the source does not exceed the maximum rating specified. Electrical shock hazard, isolate the mains before commencing any electrical works 1. Verify that the power to your current doorbell has been shut off and no voltage is present. 2. Using the smallest bolts, secure the 2 cables using the rings that are supplied, to the rear of the doorbell in the threaded terminals (marked as AC wiring terminalson the product overview diagram) . Note: These terminals are not polarity conscious 3. Connect these 2 cables to the 12 to 24V AC Power Supply Unit using either the wire nuts supplied or an alternative connection method. 4. Secure the doorbell back onto its mounting bracket, and turn the power back on. Indoor chime unit • 200 meters range (open field) • Low power consumption 5 volume levels Changing the ringtone Press ‘Change Ringtone’ button to change ringtone. Pairing The chimes do come paired with the doorbell, but if a chime needs to be paired to a doorbell follow the below: 1. Press and hold the setting button until the chime starts flashing red (this means it is in pairing mode, the pairing mode is only active for 8 seconds, then it will automatically exit) 2. Press the button on the doorbell within 8 seconds, it will ring and the chime’s indicator will flash blue 3. Press the button on the doorbell again to confirm whether the current ringtone is the one you have set, this completes pairing App pairing 1. Power up the device, and the LED on the front should b

FAQs

What safety precautions are required before installation or electrical work?

Read the instructions and retain them for future reference. Ensure the system supply is safely isolated before any electrical works, and have installations comply with the current IEE regulations.

What WiFi and mobile requirements are needed to set up the doorbell?

Connect the phone to the same 2.4GHz WiFi network. Use a mobile device with iOS 8 or higher or Android 4.1x or higher, and download the ClickSmart+ app.

How do you pair the chime with the doorbell and complete pairing?

For pairing, press and hold the chime setting button until it flashes red (pairing lasts 8 seconds), then press the doorbell button within 8 seconds. Press again on the doorbell to confirm the ringtone and complete pairing.

Oct 25, 2026

Upload by Bulrr