SK-3354 REV 01 - Installation Manual - Arnott New Front Coil-Over Strut Various GM SUVs (K2xx, w/MagneRide)

Oct 22, 2026

Installation instructions SK-3354 REV 01 (December 1, 2022) for Arnott New Front Coil-Over Strut used on various GM SUVs (K2xx) with MagneRide. The manual emphasizes proper, professional installation, vehicle lifting and immobilizing, and pressure relief up to 10 bar/150 lbf/in before disassembly. It includes general safety guidance, warnings and cautions, and step-by-step shock removal and shock installation procedures, including reconnecting electrical connections, tightening to manufacturer specifications, and completing lowering and wheel reinstall.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages8

Reading Time20 min

AccessFree to download

GENERAL INFORMATION

SHOCK REMOVAL

Steps

SHOCK INSTALLATION

Steps

INSTALLATION MANUAL SK-3354 Arnott New Front Coil-Over Strut Various GM SUVs (K2xx, w/MagneRide) Engineered to Ride, Built to Last® 1 REV 01 December 1, 2022 CONGRATULATIONS ON YOUR PURCHASE OF AN ARNOTT® SUSPENSION PRODUCT WE AT ARNOTT LLCARE PROUD TO OFFERA HIGH QUALITY PRODUCT WITH ALL THE TECHNICAL SUPPORT YOU NEED. THANKYOU FORYOUR CONFIDENCE IN USAND OUR PRODUCT. Proper installation is essential to experience and appreciate the benefits of this system. Please take a moment to review these installation instructions before you begin to install these components on your vehicle. The removal and installation of air suspension products should only be performed by a fully qualified and certified automotive professional. It is equally important to be aware of all necessary safety measures while installing your new Air Suspension System. This includes proper lifting and immobilizing of the vehicle and isolation of any stored energy to prevent personal injury or property damage. GENERAL INFORMATION Reading this manual signifies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement, the full text of which is available at [www.arnottinc.com](www.arnottinc.com) and [www.arnotteurope.com](www.arnotteurope.com). WARNING: The air suspension system is under pressure (up to 10 bar, or 150 lbf/in). Verify pressure has been relieved and disconnect power to the air suspension system prior to disassembly. Do not allow dirt or grease to enter the system. Always wear standard hand, ear, and eye protection when servicing the air suspension system. • Not to be stored below 5°F (-15°C) and above 122°F (50°C). • Avoid damage to air lines and cables. • Removal and installation is only to be performed by fully qualified personnel. • Use car manufacturer’s diagnostic software. CAUTION: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence. To avoid the possibility of short circuits while working with electric components consult your owner’s manual on how to disconnect your battery. Consult your vehicle owner’s manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur. 2 SK-3354 Installation Manual REV 01 December 1, 2022 SHOCK REMOVAL 1. Lift vehicle and remove applicable front wheel. (FIGURE 1) FIGURE 1 2. Unroute and disconnect the electrical connection. (FIGURES 2, 3) 3 SK-3354 Installation Manual REV 01 December 1, 2022 3. Remove the three (3) top mount nuts. (FIGURES 4, 5) FIGURE 4 FIGURE 5 4. Remove the two (2) bottom mount bolts. (FIGURES 6, 7) 4 SK-3354 Installation Manual REV 01 December 1, 2022 5. Remove the shock assembly from the vehicle. (FIGURE 8) FIGURE 8 6. Removal complete. 5 SK-3354 Installation Manual REV 01 December 1, 2022 SHOCK INSTALLATION WARNING: Tighten all nuts and bolts to manufacturer’s specifications during the installation process. 1. Install the assembled shock on to the vehicle. (FIGURE 9) FIGURE 9 2. Reinstall the two (2) bottom mount bolts. Tighten to manufacturer’s specifications. (FIGURE 10) FIGURE 10 6 SK-3354 Installation Manual REV 01 December 1, 2022 3. Reinstall the three (3) top mount nuts. Tighten to manufacturer’s specifications. (FIGURES 11, 12) 4. Reroute and connect the electrical connection. (FIGURES 13, 14) FIGURE 13 FIGURE 14 5. Reinstall the applicable front wheel. 6. Lower the vehicle. 7. Installation complete. 7 SK-3354 Installation Manual REV 01 December 1, 2022 Arnott US Business Office: [www.arnottinc.com](www.arnottinc.com) 100 Sea Ray Drive Merritt Island, FL 32953 Call: 800.251.8993

FAQs

What safety precautions are required before disassembling the air suspension system?

Relieve the air suspension pressure and disconnect power before disassembly. Wear standard hand, ear, and eye protection and prevent dirt or grease from entering the system.

Can the installation/removal be done by unqualified personnel?

No. Removal and installation should be performed only by fully qualified and certified automotive professionals.

What are the key steps to install the shock after removal?

Install the assembled shock, reinstall and tighten the two bottom mount bolts, reinstall and tighten the three top mount nuts, reroute and connect the electrical connection, reinstall the front wheel, and lower the vehicle.

Oct 22, 2026

Upload by Taylor Morgan