SikaQuick 1000 - Rapid hardening repair mortar with extended working time

Q: What is SikaQuick 1000 used for?

It is used for cementitious patching and repair of concrete, including highway overlays, structural repairs, and full-depth patching on concrete surfaces and related structures.

Q: What are the recommended application timing limits?

Mixing, placing, and finishing should not exceed 30 minutes maximum, and typical application life is about 30 minutes after adding powder to water.

Q: How soon can traffic be allowed after placement?

Open to foot traffic in 4 hours and to vehicle traffic in 6 hours at 73°F, with onsite testing recommended for verification of performance.

Nov 1, 2026

Uploaded by jayni

SikaQuick 1000 is a 1-component cementitious patching mortar for concrete, designed for rapid hardening and early strength gain while maintaining an extended working time. It is suitable for above/below-grade repairs, highway overlays, structural concrete roadways, parking structures, bridges, dams, ramps, and full-depth patching. The mortar offers easy placement, freeze/thaw resistance, no added chlorides, non-gypsum formulation, and early traffic access (foot in 4 hours, vehicle in 6 hours at 73°F).

LanguageEnglish

CategoryTechnology

FormatPDF

Pages2

Reading Time5 min

AccessFree to download

Product Data Sheet

Description

Where to Use

Advantages

Coverage and Packaging

Typical Data

How to Use

Surface Preparation

Priming

Mixing

Application

Curing

Construction Product Data Sheet Edition 10.2.2009 Identification No. 742 SikaQuick 1000 SikaQuick® 1000 Rapid hardening repair mortar with extended working time | Description | SikaQuick 1000 is a 1-component, rapid hardening, early strength gaining, cementitious, patching material for concrete. | | --- | --- | | Where to Use | n Use on grade, above, and below grade on concrete.
n Highway overlays and repairs.
n Structural repair material for concrete roadways, parking structures, bridges, dams and ramps.
n Full depth patching repairs.
n Economical patching material for horizontal repairs of concrete and mortar. | | Advantages | n Specially suited for hot weather applications when extended working time is required.
n Rapid hardening as defined by ASTM C-928 .
n Epoxy coatings can be applied as early as 6 hrs. Onsite testing is recommended for verification. Please consult coatings manufacturer for recommendations.
n Freeze/thaw resistant.
n Easy to use, labor-saving material.
n Contains no added chlorides.
n Not gypsum-based.
n High early strength.
n Open to foot traffic in 4 hours; to vehicle traffic in 6 hours (at 73°F) .
n Easily applied to clean, sound substrate.
n Not a vapor barrier. | | Coverage | Approximately 0.42 cu. ft. When extended with 25 lbs. of 3/8 in. gravel yield is approximately 0.58 cu. ft. | | Packaging | 50 lb. multi-wall bag. | Typical Data (Material and curing conditions @ 73°F (23°C) and 50% R. H.) (Water/powder = 0 . 10) Shelf Life 1 year in original, unopened bag. Storage Conditions Store dry at 40°-95°F (4°-35°C) . For best results, condition material to 65°-75°F before using. Color Concrete gray. Mixing Ratio Approximately 4.5-5 pints of liquid per 50 lb. bag. Application Life Approximately 30 minutes after adding powder to the water. Compressive Strength, psi 3 hours 1 day 7 days 28 days Mortar-ASTM C-109 1,250 psi (8 .6 MPa) 4,000 psi (27 .6 MPa) 5,000 psi (34 .5 MPa) 7,000 psi (48 .2 MPa) Flexural Strength, psi (ASTM C-78) 1 day 700 psi (4 .8 MPa) 7 days 900 psi (6 .2 MPa) 28 days 1,000 psi (6 .9 MPa) Splitting Tensile Strength, psi (ASTM C-496) 1 day 300 psi (2 .0 MPa) 7 days 400 psi (2 .7 MPa) 28 days 500 psi (3 .4 MPa) Bond Strength, psi (ASTM C-882) modified 1 day 1750 psi (12 .0 MPa) 7 days 2000 psi (13 .8 MPa) 28 days 2500 psi (17 .2 MPa) Direct Tensile Bond, psi (ACI 503) 28 days 300 psi (substrate failure) Drying Shrinkage,%(ASTM C-596) 28 days 0.06 Modulus of Elasticity, psi (ASTM C-469) 28 days 4.6 x 106 Chloride Permeability, Coulombs (ASTM C-1202) 28 days < 1000 Freeze/Thaw Resistance,%(ASTM C-666) 28 days 98% Scaling Resistance, lb./ft2 (ASTM C-672) 50 cycles 0.080 Initial Set, Minutes (ASTM C-266) 40-90 Final Set, Minutes (ASTM C-266) 60-120 Abrasion Resistance, Inches of Wear at 1 hr. (ASTM C-779) 28 days 0.026 *Independent certificates available upon request. Construction How to Use Surface Preparation Surface must be clean and sound. Remove all deteriorated concrete, dirt, oil, grease, and other bond-inhibiting materials from the area to be repaired. Be sure repair area is not less than 1/4 in. deep. Preparation work should be done by appropriate means. Obtain an exposed aggregate surface with a minimum surface profile of ± 1/8 in. (CSP-6) on clean, sound concrete. To ensure optimum repair results, the effectiveness of decontamination and preparation should be assessed by a pull-off test. Saw cutting of edges is preferred and a dovetail is recommended. Saturate surface to be repaired with clean water. Substrate should be saturated surface dry (SSD) prior to application. | Priming | For priming of reinforcing steel use Sika Armatec 110 EpoCem (consult Technical Data Sheet) .
Concrete Substrate: Prime the prepared substrate with a scrub coat of SikaQuick 1000 prior to placement of the mortar. The repair mortar has to be applied into the wet scrub coat b

FAQs

What is SikaQuick 1000 used for?

It is used for cementitious patching and repair of concrete, including highway overlays, structural repairs, and full-depth patching on concrete surfaces and related structures.

What are the recommended application timing limits?

Mixing, placing, and finishing should not exceed 30 minutes maximum, and typical application life is about 30 minutes after adding powder to water.

How soon can traffic be allowed after placement?

Open to foot traffic in 4 hours and to vehicle traffic in 6 hours at 73°F, with onsite testing recommended for verification of performance.

Nov 1, 2026

Uploaded by jayni