SEARS Deluxe 10-Inch Flexible Drive Table Saw - Owners Manual - General Safety Instructions for Power Tools

Oct 23, 2026

SEARS owners manual content provides safety guidance for a Craftsman table saw, emphasizing correct setup, safe operation, and protective habits. It instructs readers to ground tools properly, keep guards in place, remove adjusting keys and wrenches, maintain a clean and well-lit work area, and avoid hazardous damp environments. Additional directions cover wearing proper apparel and eye protection, securing work with clamps, avoiding overreaching, maintaining tools, disconnecting before service, and preventing accidental starts. It also warns against standing on the tool, checking damaged parts, feeding against blade rotation, and never leaving the tool running unattended, plus table-saw-specific kickback precautions and assembly requirements.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages52

Reading Time2 h 11 min

AccessFree to download

GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS

Know your power tool

Ground all tools

Keep guards in place

Remove adjusting keys and wrenches

Keep work area clean

Avoid dangerous environment

Keep children away

Make workshop child-proof

Don't force tool

Use right tool

Wear proper apparel

Use safety goggles (head protection)

Secure work

Don't overreach

Maintain tools with care

Disconnect tools

Avoid accidental starting

Use recommended accessories

Never stand on tool

Check damaged parts

Direction of feed

Never leave tool running unattended

ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS

Save This Manual For Future Reference SEARS owners manual MODEL NO. 113.241691 SAW WITH LEGS TWO CAST IRON TABLE EXTENSIONS MOTOR AND HOLD DOWN CLAMP Serial Number Model and serialnumber may be foundat the rear of the base CRAFTSMAN You should record bothmodel and serial numberin a safe place forfuture use. DELUXE 10-INCHFLEX DRIVE TABLE SAW CAUTION: ● assembly READ ALLINSTRUCTIONSCAREFULLY ● operating ·repair parts Sold by SEARS,ROEBUCK AND CO.,Chicago,IL60684 U.S.A. Part No.62965 | | | --- | GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1.KNOW YOUR POWER TOOL Read and understand the owner's manual andlabels affixed to the tool.Learn its appicationand limitations as well as the specific potentialhazards peculiar to this tool. 2.GROUND ALL TOOLS This tool is equipped with an approved 3-conductor cord and a 3-prong grounding typeplug to fit the propergrounding type receptacle.The green conductor in the cord is thegrounding wire.Never connect the green wire toa live terminal. 3.KEEP GUARDS IN PLACE in working order,and in proper adjustment andalignment. 4.REMOVE ADJUSTING KEYSAND WRENCHES Form habit of checking to see that keys andadjusting wrenches are removed from toolbefore turning it on. 5.KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents.Floor must not be slippery due to wax orsawdust. 6.AVOID DANGEROUS ENVIRONMENT Don't use power tools in damp or wet locationsor expose them to rain.Keep work area welllighted.Provide adequate surrounding workspace. 7.KEEP CHILDREN AWAY All visitors should be kept a safe distance fromwork area. 8.MAKE WORKSHOP CHILD-PROOF 一with padlocks,master switches,or byremoving starter keys. 9.DON'T FORCE TOOL It will do the job better and safer at the rate forwhich it was designed. 10.USE RIGHT TOOL Don't force tool or attachment to do a job it wasnot designed for. 11.WEAR PROPER APPAREL Do not wear loose clothing,gloves,neckties orjewelry (rings,wrist watches)to get caught inmoving parts.Nonslip footwear isrecommended.Wear protective hair covering tocontain long hair.Roll long sleeves above theelbow. 12.USE SAFETY GOGGLES(Head Protection)Wear Safety goggles(must comply with ANSI 2 | FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW
If within one year from the date of purchase,this Craftsman Table Saw fails due to a defectin
material or workmanship,Sears will repair it,free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THENEAREST SEARS
SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
This warranty applies only while this product is in use in the United States.
This warranty gives you specific legal rights,and you may also have other rights which vary
from state to state.
SEARS,ROEBUCK AND Co.,Dept.698/731A,Sears Tower,Chicago,IL 60684 | | --- | Z87.1)at all times.Everyday eyeglasses onlyhave impact resistant lenses,they are NOTsafety glasses.Also,use face or dust mask ifcutting operation is dusty,and ear protectors(plugs or muffs)during extended periods ofoperation. 13.SECURE WORK Use clamps or a vise to hold work whenpractical.It's safer than using your hand,freesboth hands to operate tool. 14.DONT OVERREACH Keep proper footing and balance at all times. 15.MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for best and safestperformance.Follow instructions forlubricatingand changing accessories. 16.DISCONNECT TOOLS before servicing;when changing accessoriessuch as blades,bits,cutters,etc. 17.AVOID ACCIDENTAL STARTING Make sure switch is in “OFF”position beforeplugging in. 18.USE RECOMMENDED ACCESSORIES Consult the owner's manual for recommendedaccessories.Follow the instructions thataccompany the accessories.The use ofimproper accessories may cause hazards. 19.NEVER STAND ON TOOL Serious injury could occur if the toolis tipped orif the cutting tool is accidentally contacted.Do not store mat

FAQs

What must be done before operating the table saw?

Do not operate the saw until it is completely assembled and installed according to the instructions, and until you have read and understood the safety information.

Why is grounding important for power tools?

The tool uses an approved 3-conductor cord and a 3-prong grounding plug. The green grounding wire must not be connected to a live terminal.

How can kickback injuries be avoided during rip-type operations?

Keep your face and body to one side of the saw blade, out of line with a possible kickback, and follow the kickback avoidance guidance listed in the table-saw safety section.

Oct 23, 2026

Uploaded by EvelynWrites