Ring Alarm Contact Sensor 2nd Gen - Z-Wave SmartStart and Classic Inclusion Manual

Nov 4, 2026

Ring Alarm Contact Sensor 2nd Gen is a wireless contact sensor for the Ring Alarm system that alerts users when a door or window opens or closes. The manual explains required setup steps in the Ring app, including triggering setup mode with the battery tab and pairing the sensor with the Ring Base Station. It also covers Z-Wave network requirements, SmartStart and Classic inclusion via QR code or DSK PIN, LED behavior during inclusion, and removal/reset procedures to reconfigure the device safely.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages7

Reading Time18 min

AccessFree to download

Introduction

Basic Setup & Installation

Z-Wave Instructions

Adding to a Z-Wave Network

Removing from a Z-Wave Network

Factory Reset Instructions

Ring Alarm Contact Sensor 2nd Gen Z-Wave Technical Manual 1 Ring Alarm Contact Sensor 2nd Gen Introduction Ring Alarm Contact Sensor 2nd Gen is a wireless sensor for the Ring Alarm system which provides users the ability to know when a door or window is open or closed. After installing the sensor on a door or window and setting up the sensor in the Ring app, monitor and receive notifications when the door or window opens or closes. The Ring Alarm Base Station is required to enable Contact Sensor 2nd Gen features and functions within the Ring app. Note: • This product can be operated in any Z-Wave™ network with other Z-Wave certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. • SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity. Ring Alarm Contact Sensor 2nd Gen – Basic Setup & Installation 1. Ensure your Ring Alarm system is disarmed. 2. In the Ring app, tap Set Up a Device > Security > Sensors to find the Contact Sensor 2nd Gen 3. Follow the in-app instructions to complete setup. a. Pull the battery tab (or reinsert the batteries) to trigger setup mode. b. Tap the button on the front to retry setup mode. Installation 1. Choose a door or window for installing your Contact Sensor 2nd Gen and companion magnet. 2. Ensure the surfaces where you plan to install your sensor and magnet are clean and free from dust or dirt. 3. Using the provided double-sided tape, peel the backing and attach the sensor to the mounting location. 4. Follow the same steps for the companion magnet ensuring the magnet is aligned with the sensor and no more than 1 inch from sensor for the “closed” position. Z-Wave Instructions Z-Wave Device Type: Notification Sensor Role Type: Reporting Sleeping Slave (RSS) • GENERIC_TYPE_SENSOR_ NOTIFICATION (0x07) • SPECIFIC_TYPE_ NOTIFICATION_SENSOR (0x01) Z-Wave Long Range This device supports both Classic Z-Wave and Z-Wave Long Range. Z-Wave Long Range capable controllers can include this device as a device in the network. Long range mode allows for a much greater operating range of the device. The device can only operate in one mode at a time, and it is dictated during the inclusion process by the controller or Base Station. To change operating modes (Z-Wave SmartStart vs. Z-Wave Long Range SmartStart), the device must be removed from the network and then re-added in the desired mode. Adding Ring Alarm Contact Sensor 2nd Gen to a Z-Wave Network Ring Alarm Contact Sensor 2nd Gen can be added via Smart Start or Classic inclusion mode. Note: When prompted for the QR Code or PIN, you may find them on the device, on the box, or on a card inside the box. Keep the device nearby. You’ll be prompted to pull the battery tab to power on the device and enter setup mode. Smart Start Inclusion Steps: 1. Initiate the add flow for Security Devices in the Ring mobile application – Follow the guided add flow instructions provided in the Ring mobile application. 2. When prompted by the mobile application, scan the QR code found on the package of the Contact Sensor 2nd Gen. The QR code can also be found on the device itself. 3. Pull the pull-tab or insert batteries, and the device will go into Smart Start inclusion mode. While in this mode, Contact Sensor 2nd Gen can be added to a Z-Wave controller that supports Smart Start. When in Smart Start inclusion mode, Smart Start can be restarted by tapping the button on the front of the device. Classic Inclusion Steps: 1. Initiate add flow for Security Devices in the Ring mobile application – Follow the guided add flow instructions provided in the Ring

FAQs

What hardware is required to use Contact Sensor 2nd Gen features in the Ring app?

The Ring Alarm Base Station is required to enable Contact Sensor 2nd Gen features and functions in the Ring app.

How does SmartStart inclusion work for the Ring Alarm Contact Sensor 2nd Gen?

In the Ring app, start the add flow for Security Devices, scan the sensor’s QR code when prompted, then power the device by pulling the battery tab or inserting batteries to enter Smart Start inclusion mode.

What is the difference between SmartStart and Classic inclusion modes?

SmartStart inclusion uses the QR code flow and adds automatically for supported controllers, while Classic inclusion uses a manual add flow with a 5-digit DSK PIN and requires pressing and holding the front button to enter Classic inclusion mode.

Nov 4, 2026

Uploaded by cryingin4k