Replacing the S-DAT - Promag, Promass, Prosonic Flow 300, 500, 500-digital, t-mass 300, 500-digital, Promag 400 Index C - Installation Instructions

Sep 17, 2026

Upload by Fez

Installation instructions for replacing the S-DAT spare part in Endress+Hauser Promag, Promass, Prosonic Flow, and t-mass measuring devices, including model variants such as digital and compact/remote transmitter versions. The document defines the applicable spare part sets, intended use requirements, and how to verify suitability via the W@M Device Viewer. It specifies authorized repair personnel based on approval type, lists safety precautions (including de-energizing, Ex documentation, custody transfer considerations, ESD protection, and seal/thread handling), and provides a structured procedure starting with spare part set overview.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages60

Reading Time2 h 31 min

AccessFree to download

1 Overview of spare part sets

2 Intended use

3 Personnel authorized to carry out repairs

4 Safety instructions

5 Symbols used

6 Tools list

7 Promag, Promass, Prosonic Flow 300, 500

t-mass 300

8 Promag, Promass, t-mass, Prosonic Flow 500-digital

9 Promag 5D4C, 5L4C, 5W4C transmitter, compact version

10 Promag 5D4C, 5L4C, 5W4C transmitter, remote version

11 Disposal

EA01278D/06/A2/04.22-00 71557508 2022-05-02 Products Solutions Services Installation Instructions Replacing the S-DAT Promag, Promass, Prosonic Flow 300, 500, 500-digital, t-mass 300, 500-digital, Promag 400 Index C Replacement of the S-DAT Promag, Promass, Prosonic Flow 300, 500, 500-digital, t-mass 300, 500-digital, Promag 400 Index C Table of contents 1 Overview of spare part sets ........................................................ 4 2 Intended use ...................................................................... 4 3 Personnel authorized to carry out repairs ........................................... 4 4 Safety instructions ................................................................ 5 5 Symbols used ..................................................................... 6 6 Tools list .......................................................................... 7 7 Promag, Promass, Prosonic Flow 300, 500, t-mass 300 ............................. 7 8 Promag, Promass, t-mass, Prosonic Flow 500-digital .............................. 15 9 Promag 5D4C, 5L4C, 5W4C transmitter, compact version .......................... 24 10 Promag 5D4C, 5L4C, 5W4C transmitter, remote version ........................... 28 11 Disposal ......................................................................... 30 Endress+Hauser 3 1 Overview of spare part sets The Installation Instructions apply to the following spare part sets: | Order number | Original spare part set | Contents | | --- | --- | --- | | 71453166 | S-DAT set, Promag 300, 400, 500 | 1 × S-DAT, unprogrammed | | 71453168 | S-DAT set, Promass, t-mass 300, 500 | 1 × S-DAT, unprogrammed | | 71453169 | S-DAT set, Prosonic Flow 300, 500 | 1 × S-DAT, unprogrammed | 2 Intended use • A defective unit can only be replaced with a functioning unit of the same type. • Only use original parts from Endress+Hauser. • Check in the W@M Device Viewer if the spare part is suitable for the existing measuring device. A spare parts overview is located in the interior of some measuring devices. If the spare parts kit is specified on this list, no inspection is required. | [www.endress.com/deviceviewer](www.endress.com/deviceviewer)

Ser. No.: 12345...
| |
| | --- | --- | --- | | | | | 3 Personnel authorized to carry out repairs Authorization to carry out repairs depends on the measuring device's approval type. The table below shows the authorized group of people in each case. Whoever carries out the repairs has full responsibility to ensure that work is carried out safely and to the required quality standard. He/she must also guarantee the safety of the device following repair. 4 Endress+Hauser | Measuring device approval | Personnel authorized to perform repairs 1) | | --- | --- | | Without approval | 2, 3 | | With approval (e.g. IECEx) | 2, 3 | | For custody transfer | 4 | 1) 1 = Qualified specialist on customer side, 2 = Service technician authorized by Endress+Hauser, 3 = Endress+Hauser (return measuring device to manufacturer) 4 = Check with local approval center if installation/alteration must be performed under supervision. 4 Safety instructions • Check whether the spare part matches the identification labeling on the measuring device, as described on the cover page. • The spare part set and the Installation Instructions are used to replace a defective unit with a functioning unit of the same type. Only use original parts from Endress+Hauser. • Comply with national regulations regarding mounting, electrical installation, commissioning, maintenance and repair. • The following requirements must be met with regard to specialized technical staff for the mounting, electrical installation, commissioning, maintenance and repair of the measuring devices: • Specialized technical staff must be trained in instrument safety. • They must be familiar with the individual operating conditions of the devi

FAQs

What spare part sets does the Installation Instructions document apply to?

It applies to S-DAT spare part sets for specific Promag, Promass, Prosonic Flow, and t-mass device groupings, listing their order numbers and contents (unprogrammed S-DAT).

When can a defective unit be replaced?

A defective unit can only be replaced with a functioning unit of the same type. Only original Endress+Hauser parts may be used, and the spare part suitability should be checked with the W@M Device Viewer when needed.

Who is authorized to carry out the repairs?

Authorization depends on the measuring device approval type. The document provides an approval-based table mapping approval categories (e.g., without approval, with approval, custody transfer) to authorized personnel groups.

Sep 17, 2026

Upload by Fez