Refrigerated Counter-Top Prep - Installation, Operation & Maintenance Manual - (HC Gas R600a Used)

Sep 27, 2026

Refrigerated Counter-Top Prep provides practical instructions for safe installation, operation, and maintenance of a countertop refrigerated unit using HC gas R600a. The manual details placement on a stable flat surface, ventilation clearances, electrical start-up and set-temperature adjustment, and food storage rules to maintain correct operating temperature. It also covers cleaning and care, including condenser cleaning and general precautions, followed by troubleshooting guidance and key technical specifications, electrical wiring, disposal, and compliance notes.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages7

Reading Time18 min

AccessFree to download

Safety Tips

Introduction

Installation

Fit Glass Panels (Optional)

Fitting unit on a Marble pizza counter (Optional)

Operation

Storing Food

Turn On

Adjusting the Set Temperature

Cleaning, Care & Maintenance

Cleaning the Condenser

Troubleshooting

Technical Specifications

Electrical Wiring

Disposal

Compliance

Refrigerated Counter-Top Prep Installation, Operation & Maintenance Manual (HC Gas R600a used) Table of Contents Safety Tips……………………………………………………………………….. 1 Introduction………………………………………………………………………1 Installation…………………………………………………………………………1 Fit Glass Panels……………………………………………………………. 1 Operation………………………………..…………………………………………2 Storing Food………………………………..……………………………………. 2 Turn On………………………………………………………………………………2 Cleaning, Care & Maintenance……………………………………………2 Cleaning the Condenser………………………………………………………2 Troubleshooting…………………………………………………………………. 2 Technical Specifications………………………………………………………. 3 Electrical Wiring………………………………………………………………….. 3 Disposal………………………………………………………………………………. 3 Compliance…………………………………………………………………………. 3 Safety Tips ⚫ Position on a flat, stable surface. ⚫ A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components or service panels on this product. ⚫ Consult Local and National Standards to comply with The following: · Health and Safety at Work Legislation · BS EN Codes of Practice · Fire Precautions · IEE Wiring Regulations · Building Regulations ⚫ DO NOT use jet/pressure washers to clean the appliance. ⚫ DO NOT use the appliance outside. ⚫ DO NOT use this appliance to store medical supplies. ⚫ DO NOT use electrical appliances inside the appliance. (e.g. heaters, ice-cream makers etc. ) ⚫ Always carry, store and handle the appliance in a vertical position and move by holding the base of the appliance. ⚫ Always switch off and disconnect the power supply to the unit before cleaning. ⚫ Keep all packing away from children. Dispose of the packaging in accordance with the regulations of local authorities. ⚫ If the power cord is damaged, it must be replaced by an agent or a recommended qualified technician in order to avoid a hazard. Introduction Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your product. We pride ourselves on quality and service, ensuring that atthe time of packing the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your dealer immediately. Installation Note: If the unit has not been stored or moved in an upright position, let it stand upright for approximately 12 hours before operation. If in doubt allow the appliance to stand. 1. Remove the appliance from the packaging. Make sure, that all protective plastic film and coatings are thoroughly removed from all surfaces. 2. Maintain a distance of 20cm (7 inches) between the unit and walls or other objects for ventilation. Increase this distance if the obstacle is a heat source. 3. Ensure the ambient temperature is within the design range of the cabinet, avoid locations below 15 degrees C. Beware of enclosed rooms with other refrigeration equipment as additional ventilation may be required. Note: Before using the appliance for the first time, clean the shelves and interior with soapy water. Thoroughly dry afterwards 3. Level the appliance by adjusting the screw feet. Fit Glass Panels(optional) 1. Screw the collars to the rim of the appliance. Note: Ensure the hole in the collar for the grub screw face Inwards. 2. Slot the two side panels into the collars, with the holes in The glass at the top. Note: Ensure the screw hole furthest from the edge of the panel goes to the back of the appliance. 3. Screw a grub screw into each collar to secure the panels. Note: Ensure the soft end of the grub screw is the end making contact with the glass. 4. Slot the rear panel into the collars, with the holes in the glass at the top. 5. Screw a grub screw into each collar to secure the panel. 6. Slot the plastic plugs into each of the holes. 7. Screw the brackets to the inside of each pane using the bolt assem

FAQs

What are the key safety requirements before installation and repairs?

Place the unit on a flat, stable surface. A service agent or qualified technician should carry out installation and any required repairs, and you should not remove components or service panels.

What ventilation clearance and temperature conditions are required for installation?

Maintain a 20 cm (7 inches) distance between the unit and walls or other objects for ventilation. Ensure ambient temperature stays within the design range and avoid locations below 15 degrees C.

How do you turn on the unit and adjust the set temperature?

Close the door(s), set the power switch to [O], turn on at the socket, then switch on the power [l]. To adjust temperature, press and hold the set button for 3 seconds, use arrow keys to select the required set temperature, press set to store, and wait about 5 seconds for display to show cabinet temperature.

Sep 27, 2026

Uploaded by eBook King