PS1000X World Football Pro - Service Manual - Rev I

Nov 4, 2026

Service manual for the PS1000X World Football Pro, including safety and warning instructions required before installation and servicing. Covers setup steps such as unboxing the pallet, game assembly, final game setup, and first-time power-on calibration. Provides guidance for programming, volume controls options, diagnostic menu access, and warranty information. Includes AC power and fuse specifications, power supply constraints, grounding and static discharge precautions, and universal card-link wiring pinouts for coin, prize meter/ticket notch, ticket run/enable, inhibit/enable, and ground.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages36

Reading Time1 h 31 min

AccessFree to download

Safety and Warnings

UCL Connector

SETUP

Unpacking Your Pallet

Game Assembly

Final Game Setup

First Time Power On (Calibration)

Programming

Volume Controls (Options and)

Diagnostic Menu

Warranty

Service Manual (716) 759-0360 WWW.ICEGAME.COM Innovative Concepts in Entertainment 10123 Main street Clarence, New York 14120 Table of Contents Safety and Warnings 3 UCL Connector 4 SETUP UNPACKING YOUR PALLET 5 GAME ASSEMBLY 8 FINAL GAME SETUP 31 FIRST TIME POWER ON (Calibration) 32 PROGRAMMING 33 VOLUME CONTROLS (OPTIONS ANDAMP) 34 DIAGNOSTIC MENU 35 WARRANTY 36 Rev I 7/20/2023 SAFETY AND WARNINGS BEFORE YOU BEGIN WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE AGROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO THE ELECTRONICS. NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY. DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME REASON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR WARRANTY. HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE GROUND IS FUNCTIONING PROPERLY. THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING PLANE OF THE GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY, WHICH COULD CAUSE DAMAGE. THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLTAGES OTHER THAN THOSE IT WAS DESIGNED FOR. PLEASE CONTACT OUR SERVICE DEPARTMENT FOR VOLTAGE CONVERSION INFORMATION. WARNING DO NOT remove any of the components on the main board (e.g. compact flash and eproms) while the game is powered on. This may cause permanent damage to the parts and the mainboard. Removing any main board component part while powered on will void the warranty. ALWAYS REMOVE POWER TO THE GAME, BEFORE ATTEMPTING ANY SERVICE, UNLESS NEEDED FOR SPECIFIC TESTING. FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS. THIS GAME IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET COULD BE USED. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. AC Power Information The games main fuse is accessed through the back of the game at the power mod. Above the power cord is a small panel that contains the main fuse. The value of the fuse for 120 volt 60Hz is 5 AMPS at 250Volt type slow blow. The value of the fuse for 220/230 volt 50/60Hz is 3 AMPS at 250 Volt type slow blow. Universal Card link Connection See Wiring Insert for wire colors and which connections are used. Pin 1. +12v-Supply to Card System = Minimum of 2A available for the card systems and a Max of 3A. Pin 2. Coin 1- input to the game PCB. Pin 3. Prize Meter/Ticket Notch 2- is connected to the Ticket Notch line between the game PCB and ticket dispenser. Optional. Pin 4. Coin Meter 1- is connected to the coin meter 1 output from the game PCB and can be used by card systems for monitoring purposes. Pin 5. Ticket Run/Enable 2- is connected to the ticket run line between the game PCB and ticket dispenser. Optional. Pin 6. Prize Meter/Ticket Notch 1- is connected to the Prize or Ticket Meter output from the game PCB and can be used by card systems for monitoring purposes. Optional. Pin 7. Coin Inhibit/Enable- is connected to the Coin or Note Inhibit/Enable output from the Game PCB and is used where the game has this feature for disabling any payment. This is normally for states like New Jersey that limit the amount of money that can be inserted at one time. Pin 8. Ticket Run/Enable 1- is connected to the ticket run line between the game PCB and ticket dispenser in standard redemption games. This is commonly used for systems using paperless or E-ticket. Not Used if the game

FAQs

What grounding requirements are specified before installing the game?

A grounded A.C. receptacle must be used. Do not defeat or remove the grounding prong; improper grounding can cause improper operation or damage and could void the warranty.

How is the main fuse accessed and what are the fuse ratings?

Access the main fuse through the back of the game at the power mod using the small panel above the power cord. Fuse ratings are 5A at 250V slow-blow for 120V 60Hz and 3A at 250V slow-blow for 220/230V 50/60Hz.

What precautions are required before attempting any service?

Always remove power to the game before attempting service unless needed for specific testing. Do not remove components on the main board while the game is powered on, as this may cause permanent damage and void the warranty.

Nov 4, 2026

Uploaded by Nguyễn Văn Học