PRO COMP SUSPENSION - PN# LL-5010 2008 - Toyota Sequoia 2WD & 4WD Spacer Kit - Installation Instructions

Oct 23, 2026

Uploaded by fresh2021

PRO COMP SUSPENSION provides installation instructions for the LL-5010 spacer kit for Toyota Sequoia 2WD & 4WD. The document emphasizes professional installation, safety precautions, inspection of steering and driveline components, verification that the kit is complete, and correct torque specifications. It includes preparation steps and a front installation sequence, including removal of wheels and skid plates, loosening control arm and strut hardware, installing the specified spacer, and aligning the strut to fit the control arm mount.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages8

Reading Time20 min

AccessFree to download

Introduction

Safety and pre-installation checks

Front Installation

Preparation and measurements

Strut, control arm, and spacer installation

2360 Boswell Road Chula Vista, CA 91914 Phone 619.216.1444 Fax 619.216.1474 E-Mail tech@explorerprocomp.com PRO COMP SUSPENSION Suspension Systems that Work! PN\# LL-5010 2008 Toyota Sequoia 2WD & 4WDSpacer Kit 1 This document contains very important information that includes warranty information and instructions for resolving problems you may encounter. Please keep it in the vehicle as a permanent record. LL-5010 Revised 3.14.08 Part \# 91-2876 91-2878 90-6610 72-043200810 73-04300830 73-04300836 Description FRONT STRUT SPACER REAR COIL SPACER HARDWARE PACK: Coil Over Spacer 7/16” GR. 8 HEX NUT 7/16” SAE FLAT WASHER 7/16” SPLIT LOCK WASHER Qty. 2 2 1 8 8 8 Ill. 1 2 - 1 1 1 Page 4 6 - 4 4 4 LL-5010 Revised 3.14.08 Introduction: ♦ This installation requires a professional mechanic! ♦ We recommend that you have access to a factory service manual for your vehicle to assist in the disassembly and reassembly of your vehicle. It contains a wealth of detailed information. ♦ Prior to installation, carefully inspect the vehicle’s steering and driveline systems paying close attention to the tie rod ends, ball joints, wheel bearing preload, pitman and idler arm. Additionally, check steering-to-frame and suspension-to-frame attaching points for stress cracks. The overall vehicle must be in excellent working condition. Repair or replace all worn or damaged parts! ♦ Read the instructions carefully and study the illustrations before attempting installation! You may save yourself a lot of extra work. ♦ Check the parts and hardware against the parts list to assure that your kit is complete. Separating parts according to the areas where they will be used and placing the hardware with the brackets before you begin will save installation time. ♦ Check the special equipment list and ensure the availability of these tools. ♦ Secure and properly block vehicle prior to beginning installation. ♦ ALWAYS wear safety glasses when using power tools or working under the vehicle! ♦ Use caution when cutting is required under the vehicle. The factory undercoating is flammable. Take appropriate precautions. Have a fire extinguisher close at hand. ♦ Foot pound torque readings are listed on the Torque Specifications chart at the end of the instructions. These are to be used unless specifically directed otherwise. Apply thread lock retaining compound where specified. ♦ Please note that while every effort is made to ensure that the installation of your Pro Comp lift kit is a positive experience, variations in construction and assembly in the vehicle manufacturing process will virtually ensure that some parts may seem difficult to install. Additionally, the current trend in manufacturing of vehicles results in a frame that is highly flexible and may shift slightly on disassembly prior to installation. The use of pry bars and tapered punches for alignment is considered normal and usually does not indicate a faulty product. However, if you are uncertain about some aspect of the installation process, please feel free to call our tech support department at the number listed on the cover page. We do not recommend that you modify the Pro Comp parts in any way as this will void any warranty expressed or implied by the Pro Comp Suspension company. LL-5010 Revised 3.14.08 Please read instructions thoroughly and completely before beginning installation. Installation by a trained mechanic is recommended Front Installation: 1. Position your vehicle on a smooth, flat, hard surface (i.e. concrete or asphalt) . Block the rear tires and set the emergency brake. 2. Measure and record the distance from the center of each wheel to the top ofits fender opening. Record below. LF: RF: LR: RR: 3. Lift vehicle by the frame so that the front wheels are off the ground using a floor jack and jack stands or a (2) two post lift if available. 4. First, remove the skid

FAQs

What are the prerequisites before starting the LL-5010 installation?

The instructions require a professional mechanic and recommend access to a factory service manual. Before installing, inspect the steering and driveline systems, repair or replace worn parts, and confirm the kit completeness against the parts list.

What safety precautions does the document emphasize?

Always wear safety glasses when using power tools or working under the vehicle. Use caution when cutting under the vehicle because factory undercoating is flammable, and keep a fire extinguisher nearby.

How is the strut spacer installed during the front installation?

Install the strut spacer (91-2876) and torque to factory specs, then reinstall the strut. Use the provided 7/16” hardware without tightening initially, guide the lower strut mount using a jack, torque the mounting bolt and nut to factory specs, and apply thread locker if necessary. Note the strut must be clocked 45 degrees after the top is bolted in place.

Oct 23, 2026

Uploaded by fresh2021