Powered USB Hub/USB 2.0 Redriver in A-dec Equipment - Installation Guide

Sep 27, 2026

Uploaded by moss~

Installation Guide for integrating a Powered USB Hub/USB 2.0 Redriver into A-dec equipment. The guide covers supported A-dec delivery system models and revisions, describes what is new in the release, and lists recommended tools. It provides step-by-step procedures to turn off system power, remove delivery system covers for different model families, manage shock and static-discharge hazards, secure wrist and grounding straps, and points to the next step for positioning the USB hub/redriver.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages16

Reading Time40 min

AccessFree to download

Turn off the Power to the System

Remove the Delivery System Cover

Remove the Cover for A-dec 332pro/333pro/334pro/335pro/336pro/342pro Delivery System

Remove the Cover for A-dec 532pro/532B Delivery System

Raise the Cover on the A-dec 533pro/533B Delivery System

Remove the Delivery System Covers from an A-dec 541pro/541B Delivery System

Next step

Position the USB Hub/Redriver

Installation Guide Powered USB Hub/USB 2.0 Redriver in A-dec® Equipment Product Models and Versions Covered in This Document* | Models | Versions | Description | | --- | --- | --- | | 332pro/333pro | n/a | Delivery System | | 332/333 | A | Delivery System | | 532pro/533pro/541pro | n/a | Delivery System | | 532/533/541 | B | Delivery System | *Equipment shown in this document may include optional features or accessories. Some product models, versions, and options in this document may not be available in certain regions. What’s New in This Release The following updates have been made in this revision: • Images have been updated to reflect the 500 Pro Delivery Systems. • Steps for installing the redriver have been added. Before You Begin Recommended Tools • Diagonal cutters • Anti-static wrist strap • Wire strippers • Standard and Phillips head screwdrivers • Umbilical snake 86.0770.00 Rev D Powered USB Hub/USB 2.0 Redriver in A-dec Equipment Installation Guide Turn off the Power to the System WARNING Failure to turn off or disconnect the power before you begin this procedure can lead to product damage and result in serious injury or death. 1. Use the master toggle to turn off the power to the system. Remove the Delivery System Cover Continue with the section for the appropriate delivery system: Remove the Cover from the A-dec 332pro/333pro/334pro/335pro/ 336pro/342pro Delivery System .............................. 2 Remove the Cover from the A-dec 532pro/532B Delivery System ...................................... 4 Remove the Cover from the A-dec 532pro/532B Delivery System .............................. 4 Remove the Delivery System Covers from an A-dec 541pro/541B Delivery System .................. 6 Remove the Cover from the A-dec 332pro/333pro/334pro/335pro/ 336pro/342pro Delivery System WARNING Shock hazard. When you remove or replace the covers, take care not to damage any wiring or tubing. Verify that the covers are secure after you replace them. 1. Remove the back cover: ○ New-style cover—Locate the lift slots in the front corners of the control head and pull the cover up to disengage it from the control head, and then lift the cover at all four corners to remove it from the control head. 332pro Delivery System Shown ○ Old-style cover—Use a 7/64" hex key to remove the two screws securing the control head back cover and then remove the cover. 2 86.0770.00 Rev D Powered USB Hub/USB 2.0 Redriver in A-dec Equipment Installation Guide 2. Continental systems only: (1) Remove the tubing from the whips and drape them over the front of the control head. (2) Remove the whips from the control head. (3) Lift the corner of the instrument pad and carefully pull it away from the control head. 3. Use a 7/64" hex key to remove the screws securing the front cover, and then lift up the front cover. ATTENTION Circuit boards are sensitive to static electricity. Electrostatic Discharge (ESD) precautions are required when touching a circuit board or making connections to or from the circuit board. Circuit boards should be installed only by an electrician or qualified service person. 4. Secure a grounding strap to your wrist and the other end to a grounding location in the control head. Next step See “Position the USB Hub/Redriver” on page 8 . 86.0770.00 Rev D 3 Powered USB Hub/USB 2.0 Redriver in A-dec Equipment Installation Guide Remove the Cover from the A-dec 532pro/532B Delivery System 1. Swivel the touch control to the side. 532pro Shown 2. Push up on the cover release at the back of the control head and lift the top cover off the control head. 532B Shown 4 86.0770.00 Rev D Powered USB Hub/USB 2.0 Redriver in A-dec Equipment Installation Guide ATTENTION Circuit boards are sensitive to static electricity. Electrostatic Discharge (ESD) precautions are required when touching a circuit board or making connections to or from the circuit boar

FAQs

What safety warnings are emphasized before installing the redriver?

The guide warns to turn off or disconnect power before starting to avoid product damage and serious injury or death. It also stresses shock hazard and careful handling when removing or replacing covers to avoid damaging wiring or tubing.

Which tools are recommended for this installation procedure?

Recommended tools include diagonal cutters, an anti-static wrist strap, wire strippers, standard and Phillips head screwdrivers, and an umbilical snake.

How does the guide handle electrostatic discharge (ESD) risks?

It instructs that circuit boards are sensitive to static electricity and that ESD precautions are required when touching a circuit board or making connections. It also states boards should be installed only by an electrician or qualified service person, and directs the user to secure an anti-static wrist strap and connect it to a grounding location.

Sep 27, 2026

Uploaded by moss~