PDX-2808 PDX-2808 DUO - USER’S MANUAL

Nov 4, 2026

Uploaded by acoobca

PDX-2808 PDX-2808 DUO handset and base user manual covering device overview, handset controls and display indicators, base functions, and step-by-step installation. It explains power and phone line connections, handset and extra handset battery installation using rechargeable NiMH batteries, and charging for proper setup. It also provides call operations including receiving calls, hands-free speaker control, ending calls, and dialling methods such as direct dial, pre-dial, pause insertion, keypad correction, and calling from phonebook memory and caller-ID.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages52

Reading Time2 h 11 min

AccessFree to download

Overview

Handset

Display

Base

Installation

Base station

Handset

Extra handset and charger (PDX-2808 DUO)

Calling

Receiving calls

Calling with the phone or hands-free function

Ending calls

Dialling numbers

USER’S MANUAL PDX-2808 PDX-2808 DUO 1 OVERVIEWS 1.1 HANDSET: handset speaker display, see the next paragraph direct memory buttons indicator; flashes when receiving a call, remains lit when the BOOST function is enabled button, see the next page and buttons, see the next page telephone function buttons, see the next page keypad, see the next page handset microphone recharge contacts, to recharge the handset battery by placing the handset onto the cradle/charger direct memory buttons R button: function button for certain telecom services in standby mode, press to open the menu BOOST button: during a call, press to enable the extra amplifier and buttons: during a call, press to increase or decrease the volume during setup, press to confirm your settings correction button when entering phone numbers or names during setup, press to go back one step in stand-by mode, press to start an intercom call (PDX-2808 DUO only) during a call, press to switch off the microphone press to answer an incoming call or to start a phone conversation during a call, press again to enable or disable the speaker function press to end a call press and hold (> 5 sec. ) to switch off the handset in standby mode, press to open the Caller-ID memory in standby mode, press to open the last dialled number memory press to scroll through memories or settings 0-9 buttons: to dial phone numbers and to enter memories ‘asterisk’ and ‘pound’ buttons: used for e.g. telecom banking + extra: button *: press and hold 2 seconds to lock and unlock the keyboard button \#: press and hold 2 seconds so switch-OFF and ON the ringer signal 1.2 DISPLAY: handset name (HS) and internal number (1) flashes when the connection between the handset and base is lost remains lit when the handset is within range of the base flashes when receiving an external call remains lit during a call flashes when receiving an internal call remains lit during an intercom call illuminates when the speaker function is enabled illuminates when checking the Caller-ID memory and having new calls shows the status of the rechargeable batteries: = batteries are full = batteries are 2/3 full = batteries are 1/3 full, recharge as soon as possible = batteries are empty, the handset will switch off and you can no longer make calls the battery symbol will scroll while charging until the batteries are fully charged illuminates when the number is too long to be shown in the display (press the \# button to see the rest of the number) illuminates when you’ve receiver a voicemail message (only FSK systems) illuminates when the alarm (wake-up) function is enabled illuminates when the ring volume is set to 0 (switched off) 1.3 BASE: page button: to page all handsets (handset search button), also used for registering new handsets. charging contacts:the rechargeable batteries in the handset are charged via these contacts 2 INSTALLATION 2.1 BASE STATION: Telephone connection: Plug the small connector at the phone cable into the back of the base station (press the connector until you hear a click) . Plug the phone connector into the phone socket. Power supply: Connect the supplied power adaptor to the input at the rear of the base and insert the adaptor into a 230V wall socket. ONLY CONNECT THE INCLUDED ADAPTER. CONNECTING OTHER ADAPTERS MAY RESULT IN DANGEROUS SITUATIONS OR MAY CAUSE DAMAGE TO THE ELECTRONICS OF THE PHONE. Power adaptor input Phone line input 2.2 HANDSET: 1. Open the battery compartment of the handset, by sliding the battery cover down. 2. Insert the batteries into the battery compartment; at this, pay attention to the polarity (+ and-) . 3. Slide the battery cover back onto the handset and place the handseton the base station. 4. Leave the handset continuously during 15 hours on the base station, to charge the batteries properly. INSERT ONLY RECHARGEABLE NiMH (

FAQs

How do I connect the base station to the telephone line and power?

Connect the small connector on the phone cable to the back of the base until it clicks, then plug the phone connector into the phone socket. Connect the supplied power adaptor to the input at the rear of the base and plug it into a 230V wall socket only using the included adapter.

What type of batteries should be used in the handset, and how long should they charge?

Use rechargeable NiMH (nickel metal hydride) batteries only. After inserting the batteries, place the handset on the base station for 15 hours continuously to charge the batteries properly.

How can I make calls and control the speaker during a call?

For direct dialing, press the phone-on key, wait for dial tone, then enter the number and press the Call button. During a call, press the Call button again to switch on the speaker function, and press again to switch it back off.

Nov 4, 2026

Uploaded by acoobca