Operator PAD Layout / Options - Enhanced Rebar Detail - 10 to 12" Pad Thickness Was 8 to 10"

Oct 29, 2026

Upload by Tirek

Operator pad layout drawings and options for an AutoGate Gate Entry Systems installation in Berlin Heights, Ohio, specifying conduit and stub-up placement relative to public and private/secured sides. Provide two pad reinforcement approaches, including rebar arrangement and securely tying intersecting points, with embedment below local frost depth and defined top pad thickness. Include notes on conduit types and possible conduits, minimum setback, concrete compressive strength (3000 PSI), and references superseded by governing codes and site requirements. The drawing includes revision history, confidentiality notice, and dimensional units in inches.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages5

Reading Time13 min

AccessFree to download

Pad reinforcement options

Option #1: Rebar arrangement

Option #2: Full concrete pad with tied re-bar

Conduit and operator pad layout

Public side stub-out conduits

Private/secured side conduit possibilities

Installation notes and requirements

| KAY 11/5/15 |

68" REF.

68" REF.

OPTION \#1:
REBAR ARRANGEMENT (SECURELY WIRE TIE ALL 9 INTERSECTING POINTS)

28" REF.
REBAR ARRANGEMENT (SECURELY WIRE TIE ALL 13 INTERSECTING POINTS)

12" REF. TYP.
84"
48"

OPTION \#1:

Ø12" TYP.
BELOW LOCAL FROST DEPTH (3' MIN. )

(4) or (5) MIN. 12" AUGURED HOLES,
WITH WIRE TIED RE-BAR, ON 10" TO 12" TOP PAD
NOTES:

10" to 12" TOP PAD THICKNESS

6"-8"
BELOW LOCAL FROST DEPTH (3' MIN. )

OPTION \#2:
FULL CONCRETE PAD WITH TIED RE-BAR WHERE APPLICABLE PER GOVERNING CODE OR STANDARD.

1)
2)
3)
4)
5)
5)
ALL PAD DEPTHS SHOULD BE BELOW LOCAL FROST DEPTH TOP OF PAD MUST BE FLAT AND LEVEL
USE REBAR THAT CONFORMS WITH LOCAL CODES OR JOB SPECS.
REBAR MUST BE INSTALLED 6"-8" BELOW TOP SURFACE.
CONCRETE COMPRESSIVE STRENGTH MINIMUM 3000 PSI.
DRAWING IS FOR REFERENCE ONLY, SUPERCEDED BY LOCAL AND SITE GOVERNING CODES
C:\USERS\BFRITZ2\DESKTOP\102-P PAD LAYOUT. DWG
Rev.: C
B
A
Description:
ENHANCED REBAR DETAIL
10" TO 12" PAD THICKNESS WAS 8" TO 10"
CONDUIT LOCATIONS WERE MOVED OUTSIDE THE PAD
Date: 11/5/15 01/24/13
07/18/08
DO NOT SCALEDrn. By: Ckd. By:
KAY
SLD
MKS
DMR
KLL
DMR
NOTICE
THE INFORMATION CONTAINED ON THIS DOCUMENT IS CONFIDENTIAL. ANY DISSEMINATION, UNAPPROVED DISCLOSURE OR COPYING OF THIS INFORMATION IS STRICTLY PROHIBITED
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES
ANGLES ± 1° X/X ± 1/32, .XX ± .01, .XXX ± .005
Date: 12/21/05
Drn. By: MKS
Ckd. By: DMR
AutoGate
Gate Entry Systems
Berlin Heights, Ohio FAX (419) 588-3514
Dwg.: 102-P
Title: Operator PAD Layout / Options
| | --- | --- | | RIGHTHAND OPERATOR

CONDUIT LOCATION / STUB-UP ON OUTSIDE OF OPERATOR PAD.
PUBLIC SIDE
(STUB OUT CONDUITS 12")
3" MIN. SETBACK

9 1/2"REF.

18 1/2"

48"

84"
PRIVATE/SECURED SIDE * NOTE: TYP 3/4" CONDUIT
POSSIBLE CONDUITS
* 120 VAC, MIN. 15 AMP CIRCUIT * FREE EXIT LOOP
* "ENTRANCE" KEYPAD * OFFICE COMMUNICATION
* "EXIT" KEYPAD * IFR BEAM POWER
* REVERSING/SAFETY LOOPS * OPTIONAL SPARES | | | | | | | | | | | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | | | | | | | | NOTICE | Date: 12/07/05 | | AutoGate
Gate Entry Systems
Berlin Heights, Ohio FAX (419) 588-3514 | | | | | | | | THE INFORMATION CONTAINED ON THIS DOCUMENT IS CONFIDENTIAL. ANY DISSEMINATION, UNAPPROVED DISCLOSURE OR COPYING OF THIS INFORMATION IS STRICTLY PROHIBITED | | | | | | | | | | | | Drn. By: MKS | | | | | | | | DO NOT SCALE | | | | | | | | Rev.:
C
B
A | Description: | Date: | Drn. By: | Ckd. By: | | Ckd. By: DMR | | | | | | RIGHTHAND OPERATOR WAS VPL OPERATOR | 04/29/15 | MKS | KAY | | Dwg.: 102C-R | | | | | | | | | | UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES
ANGLES ± 1° X/X ± 1/32, .XX ± .01, .XXX ± .005 | | | | | | | UPDATED PRINT | 1/24/13 | SLD | DMR | | | | | | | | | | | | | Title: Conduit Pad Location (Righthand) | | | | | | CONDUIT LOCATIONS WERE MOVED OUTSIDE THE PAD | 07/18/08 | MKS | DMR | | | | | MKS 04/29/15 C:\USERS\BFRITZ2\DOCUMENTS\DOCUMENTS\AUTOGATE SPEC TECH AND VIDEO\STD VPL DWG DRAWINGS\102C-R CONDUIT PAD LOCATION RH. DWG (RIGHT HAND IS MIROR IMAGE)

FAQs

What are the two reinforcement options shown for the operator pad?

Option #1 specifies a rebar arrangement with securely wire-tying all intersecting points and notes on wire-tied rebar in the top pad zone. Option #2 calls for a full concrete pad with tied re-bar where applicable per governing code or standard.

How deep must the rebar be installed relative to the top surface?

Rebar must be installed 6"-8" below the top surface, and pad depths should be below the local frost depth with the top of the pad flat and level.

Which conduit requirements and possible conduits are referenced for the right-hand operator pad?

The drawing indicates a typical 3/4" conduit and provides possible conduits such as 120 VAC for a minimum 15 amp circuit, entrance and exit keypads, free exit loop, office communication, IFR beam power, reversing/safety loops, and optional spares, with conduit stubs located on the outside of the operator pad.

Oct 29, 2026

Upload by Tirek