MultiChoice Valve Trim Installation Instructions - 17 Series - Owner’s Manual

Oct 22, 2026

Installation and owner guidance for a Delta MultiChoice valve trim in the 17 Series, covering required ASME/CSA/ASSE compliance, installer setup responsibilities, and safe temperature control. Emphasizes proper rotational limit stop adjustment at installation and potential readjustment with seasonal inlet water temperature changes. Includes warnings about burn risk, the need to inform the owner/user, labeling steps, and restrictions on installing shut-off devices on valve outlets. Also provides warranty terms, parts replacement information, and care/maintenance references.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages42

Reading Time1 h 46 min

AccessFree to download

Warranties

Installation Instructions

Clean and Care

Maintenance

Cartridge Summary Reference Sheet

Replacement Parts

CLICK ANYWHERE on THIS PAGE to RETURN to ANTI-SCALD PROTECTION GUIDES at [InspectApedia.com](InspectApedia.com) MultiChoice® Valve Trim Installation Instructions ASME A112 .18. 1 / CSA B125 .1 Write purchased model number here. Owners Manual 17 Series 68882 You May Need Table of Contents: Warranties ................................................................................. Page 2 Installation Instructions ............................................................. Pages 3-7 Clean and care........................................................................... Page 8 Maintenance .............................................................................. Page 8 Cartridge Summary Reference Sheet ....................................... Page 8 Replacement Parts .................................................................... Pages 9-24 THIS VALVE MEETS OR EXCEEDS THE FOLLOWING STANDARDS: ASME A112.18. 1/ CSA B125.1 and ASSE 1016 (Type-P-or-T-). CAUTION: This system/device must be set by the installer to ensure safe, maximum temperature. Any change in the setting may raise the discharge temperature above the limit considered safe and may lead to hot water burns. NOTICE TO INSTALLER: CAUTION!–As the installer of this valve, it is your responsibility to properly INSTALL and ADJUST this valve per the instructions given. This valve does not automatically adjust for inlet temperature changes, therefore, someone must make the necessary Rotational Limit Stop adjustmentsat the time of installation and further adjustments may be necessary due to seasonal water temperature change. YOU MUST inform the owner/user of this requirement by following the instructions. If you or the owner/user are unsure how to properly make these adjustments please refer to page 7 and if still uncertain, callus at 1-800-345-DELTA. After installation and adjustment, you must affix your name, company name and the date you adjusted the Rotational Limit Stop to the caution label provided and apply or attach the label to the back side of the closest cabinet door and the warning label to the water heater. Leave this Instruction Sheet for the owner’s/user’s reference. WARNING: This pressure balanced or thermostatic bath valve is designed to minimize the effects of outlet water temperature changes due to inlet pressure changes, commonly caused by dishwashers, washing machines, toilets and the like. It may not provide protection from hot water burns when there is a failure of other temperature controlling devices elsewhere in the plumbing system, if the rotational limit stop is not properly set or if the hot water temperature is changed after the settings are made or if the water inlet changes due to seasonal changes. WARNING: Do not install a shut-off device on either outlet of this valve. When this type of device shuts off the water flow, it can defeat the ability of the valve to balance the hot and cold water pressures. E T 17 Series 17 Ser ies 17 Series N O [www.deltafaucet.com](www.deltafaucet.com) 1 1/14/14 Rev. G | Lifetime Faucet and Finish Limited Warranty | | | --- | --- | | Parts and Finish
All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
Electronic Parts and Batteries (if applicable)
Electronic parts (other than batteries), if any, of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for 5 years from the date of purchase or, for commercial users, for one year from the date of purchase. No warranty is provided on batteries.
Delta Faucet Company will replace, FREE OF CHARGE, during the applicable warrant

FAQs

What is the installer’s responsibility for safe temperature settings?

The installer must properly install and adjust the valve per the instructions. The system/device must be set by the installer to ensure safe, maximum temperature.

Why might the rotational limit stop need readjustment after installation?

Because the valve does not automatically adjust for inlet temperature changes, rotational limit stop adjustments may be necessary at installation and again if seasonal water temperature changes occur.

What warning applies to shutting off water on this valve?

Do not install a shut-off device on either outlet of the valve, because shutting off water flow can defeat the valve’s ability to balance hot and cold water pressures.

Oct 22, 2026

Upload by AditGamingID