Model Shredder - Features & Specifications - Radio Guide & Battery Charging Instructions

Oct 25, 2026

Model Shredder manual content covering core vehicle setup and safe operation. Lists key powertrain hardware such as a 1300KV brushless electric motor, brushless 80A ESC, 2.4GHz radio system, forward/reverse capability, and 4-wheel drive suspension details. Includes vehicle scale and dimensions, LIPO battery voltage limits with a warranty warning, transmitter/receiver overview, steering and throttle reverse/trim/dual rate adjustments, binding procedure steps, plus charging guidance covering balance plug use, charge-time calculations, connector precautions, and warnings to unplug from the ESC before charging.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages9

Reading Time23 min

AccessFree to download

FEATURES & SPECIFICATIONS

Vehicle Battery Capabilities

VEHICLE OVERVIEW

Steering and Throttle Controls

Binding

CHARGING BATTERIES

Charge Time Calculations

Battery Connection Instructions

M□DEL:SHREDDER MAN-SHREDDER-2017.9.19 ·To ensure that you are using the most recent version of this manual:www.redcatracing.com/manuals/SHREDDERMANUAL.pdf ·To ensure that you have the most recent version of the Electronic Vehicles Manual:www.redcatracing.com/manuals/ELECTRIC-MANUAL.pdf ·1300KV Brushless Electric Motor ·Brushless 80A ESC ·Forward &Reverse ·4 Wheel Drive ·Aluminum Capped Oil Filled BigBore Shocks ·2.4GHz Radio System G:Upper Suspension Link A:On/Off Switch B:2.4GHz Receiver C:ESC D:Electric Motor E:Steering Servo F:Steering Linkage H:Oil Filled Shocks I:Battery Boxes J:Battery Straps # FEATURES & SPECIFICATIONS ·Scale:1/6 ·Length:670mm ·Width:430mm ·Height:230mm ·Wheelbase:480mm ·Ground Clearance:76mm # Vehicle Battery Capabilities Minimum LIPO voltage:11.1V Maximum LIPO voltage:14.4V Warning:Exceeding the maximum battery voltage may cause damage to the motor and electronic|components of this vehicle and will void the vehicle warranty. # VEHICLE OVERVIEW | | Shredder
RADIO GUIDE
RCR-2CENR
THROTTLE
STEERING
ANTENNA
REVERSE
2.4 GHZ RADIO
NORMAL
REVERSE
STEERING
BIND PLUG
CONTROL PANEL
WHEEL
STATUS
POWER
THROTTLE
TRIGGER
/
-FAILSAFE
RECEIVER
THROTTLE
STEERING
STEERING
TRIM
DUAL RATE
BINDNCC
CH3
ESC
ON
STEERING
RADIO: | | --- | --- | | Steering Reverse Switch:Top left switch.
Used to change steering orientation.If the
car turns right when you steer left,flip this
switch.
Throttle Reverse Switch:Top right switch.
Used to change throttle trigger orientation.If
the car goes in reverse while you pull the
throttle trigger,flip this switch.
Power LED:Left LED light.Lights up when
the transmitter is turned on.
Status LED:Right LED light.Lights up
green when transmitter batteries are full.
Flashes when transmitter batteries are low
and need replacing.
Bind Button:Used to bind the transmitter to
the receiver.See binding instructions.
Steering Trim:Left knob.Used to set the
steering neutral point.If the vehicle veers in
one direction while the steering wheel is cen-
tered,turn this knob in the opposite direction
until the car drives straight.
Throttle Trim:Middle knob.Used to set the
throttle neutral point.If the vehicle moves
forward or reverse while the throttle trigger is
centered,turn this knob until the vehicle re-
mains still.For maximum setting,turn slowly
until the vehicle creeps forward,then turn the
knob the opposite direction until the car
stops.
Steering Dual Rate:Right knob.Used to
limit the amount of steering.0=little/no
steering &100=maximum steering.Set the
knob to the amount of steering you feel com-
fortable with.If the vehicle has a tendency to
spin out,lower the steering rate. | On/Off Switch:Bottom switch.Turns trans-
mitter On and Off.
RECEIVER:
BIND/VCC:Used when binding to transmitter.
Ch3:Used for 3rd channel when needed.
Ch2:Used for electronic speed controller
(ESC).
Ch1:Used for steering servo.
Failsafe Button:Used to set failsafe.
BINDING:
1.Insert the BIND PLUG into the receiver BIND
port.
2.Make sure your ESC is plugged into CH2,
and insert the bind plug into BIND/CH3.
Now,power the vehicle on and the receiverr
light should begin to blink red.
3.Press the BIND button in the center of the
transmitter's Control Panel and turn on radio.
4.Release the bind button when you see the
green light on the radio flashing.At this
point,your receiver's LED should now be
solid red.Turn off the power to your vehicle,
as well as the radio.
5.Remove the BIND PLUG from the receiver.
Make sure the servos and ESC

FAQs

What LiPo voltage range does the vehicle support, and what happens if exceeded?

The manual specifies a minimum LiPo voltage of 11.1V and a maximum of 14.4V. Exceeding the maximum may damage the motor and electronic components and will void the vehicle warranty.

How do you change steering and throttle direction on the transmitter?

Use the Steering Reverse Switch to change steering orientation; flip it if the vehicle turns opposite of intended. Use the Throttle Reverse Switch to change throttle trigger orientation; flip it if the vehicle goes in reverse when pulling the throttle trigger.

What is required before charging a LiPo battery?

Unplug the battery pack from the vehicle and disconnect it from the ESC before charging. The LiPo balance plug must be connected to a LiPo balance charger, and never quick charge LiPo batteries using the power plug.

Oct 25, 2026

Upload by WPS_1790064749