Manual de Remachadora - Instruções de segurança - Uso, avaliação de riscos e manutenção

Oct 29, 2026

Upload by nayy☆

Manual for fastening blind rivets in sheet metal, aluminum, plastic, or metal profiles, covering job identification, task requirements, and safety-critical procedures. Includes a risk assessment with hazard, consequence, probability, and severity, plus preventive and corrective measures for finger entrapment, eye injuries from stem projection, cuts, and muscle strain. Provides step-by-step instructions for use, warnings against unsafe operation, and guidance for cleaning, inspection, storage, and recycling. Ends with contact details for customer support and further assistance.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages3

Reading Time8 min

AccessFree to download

Job identification and tasks

Risk assessment

Preventive measures

Corrective measures in case of accident

Instructions for use

Considerations before use

Considerations during use

Warnings

Maintenance and storage

Contact and support

1. JOB IDENTIFICATION AND TASKS Manual tool used for fastening blind rivets in materials such as sheet metal, aluminum, plastic, or metal profiles. Ideal for permanent assemblies in construction, plumbing, HVAC, or lightweight structures. 2. RISK ASSESSMENT 2.1. Risk Identification • Finger entrapment when operating the tool. • Projection of metal stems during rivet breakage. • Cuts from contact with sharp edges of the materials being joined. • Muscle fatigue or excessive strain due to continuous repetitive use. 2.2 Risk Assessment | Hazard | Consequence | Probability | Severity | Risk | | --- | --- | --- | --- | --- | | Entrapment | Finger injury | Medium | Medium | Medium | | Stem projection | Eye injury | Medium | High | High | | Cuts | Minor or moderate injuries | Medium | Medium | Medium | | Muscle fatigue | Pain or tendinitis | High | Medium | High | 2.3. Preventive Measures • Wear protective goggles and resistant gloves. • Ensure the rivet is of the correct type and size. • Avoid placing fingers near the head when operating the rivet gun. • Maintain an ergonomic posture and take breaks during prolonged work. • Check the tool before use and clean the nozzles after each job. 2.4. Corrective Measures in Case of Accident • Entrapment injury: Stop the activity, apply ice, and seek medical advice if swelling or persistent pain occurs. • Eye injury: Rinse with clean water and seek medical attention if discomfort persists. • Cuts: Clean, disinfect, and cover the wound. Seek medical advice if the injury is deep 2.5. Evaluation of the Effectiveness of the Measures • Regularly check the condition of the rivet gun and ensure compliance with the use of PPE. Ensure that operators are properly trained. 3. INSTRUCTIONS FOR USE 3.1. Considerations Before Use • Check that the rivet gun is clean, free of wear, and fitted with the correct nozzle. • Ensure the rivet is compatible with the thickness and material to be joined. • Secure the workpiece on a stable surface. • Wear PPE, including gloves and safety goggles. 3.2. Considerations During Use • Insert the rivet stem into the nozzle. • Place the rivet body into the hole of the parts to be joined. • Operate the handles progressively until the stem breaks. • Remove the broken stem from the nozzle before inserting a new one. 3.3. Warnings • Do not reuse rivets or force the tool. • Do not cut or modify the stems manually. • Do not point the tool at people or handle it unsafely. • Do not allow use by minors or untrained persons. • Do not use without eye protection or in low-visibility conditions. • Check the rivet joint to ensure it has been properly applied. • Use only under adequate lighting conditions. • Do not use the tool if you are fatigued, under the influence of alcohol, or have taken medication or substances incompatible with the task. 4. MAINTENANCE AND STORAGE 4.1. Cleaning Clean with a dry cloth after each use. Remove metal shavings and debris from the nozzle area. 4.2. Inspection Check that the nozzles are not blocked or deformed. Ensure that the handles and joints move smoothly. 4.3. Storage Store in a closed position, in a dry and protected place. Do not store with rivets inside the nozzle. 4.4. Recycling and Environment Dispose of the tool at an appropriate recycling facility in accordance with local regulations. Broken stems must be disposed of as metal waste. 5. CONTACT AND SUPPORT If you have any questions or require further assistance, please do not hesitate to contact our customer service: • Email: comercial@bellota.com • Phone: 0034 943 73 90 00 • [Website](Website: www.bellota.com)[:](Website: www.bellota.com)[ ](Website: www.bellota.com)[www.bellota.com](Website: www.bellota.com) We appreciate your trust in our products and are committed to ensuring your safety and satisfaction.

FAQs

What main hazards should operators watch for when using the rivet tool?

Key hazards include finger entrapment, eye injury from metal stem projection during rivet breakage, cuts from sharp material edges, and muscle fatigue or excessive strain from repetitive use.

What preventive and corrective measures are recommended for accidents?

Preventive measures include wearing protective goggles and resistant gloves, using the correct rivet type and size, keeping fingers away from the tool head area, maintaining an ergonomic posture, and checking the tool before use. For corrective actions, stop the activity and apply ice for entrapment injuries, rinse eyes with clean water for eye injuries, and clean, disinfect, and cover cuts, seeking medical advice if needed.

How should the tool be operated and maintained between jobs?

Before use, ensure the gun is clean, unworn, fitted with the correct nozzle, and the rivets match the joined material and thickness. During use, insert the rivet stem into the nozzle, place the rivet body into the hole, progressively operate the handles until the stem breaks, and remove the broken stem before inserting a new one. After each use, clean with a dry cloth, remove shavings from the nozzle area, inspect nozzles and handle movement, and store the tool in a dry protected place without rivets inside the nozzle.

Oct 29, 2026

Upload by nayy☆