Klean-Strip Concrete and Metal Prep - Directions for Use

Sep 27, 2026

Klean-Strip Concrete and Metal Prep is a multi-purpose product that removes rust from iron and steel, treats metal surfaces to improve paint adhesion, and etches concrete so paint or stains can penetrate and adhere. The directions explain how to prepare surfaces, apply the product by brushing, spraying, or diluting as required, allow drying or neutralization, then rinse and promptly apply paint within 48 hours. Safety guidance covers protective gloves and goggles, ventilation, first aid for swallowing and eye or skin contact, and warnings about burns and irritation.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages1

Reading Time3 min

AccessFree to download

DIRECTIONS FOR USE:

FOR RUSTED SURFACES (To Remove Rust)

FOR TREATING METAL FOR PAINTING (Phosphotizing)

FOR ETCHING CONCRETE (Before Applying a Coating)

IMPORTANT & DANGER INFORMATION

Klean-Strip Concrete and Metal Prep does the job of three products: (1)Removes rust from iron and steel surfaces,2)treats metal surfaces,including galvanized andaluminum,to allow better paint adhesion,and(3)etches concrete to allow paint or stains topenetrate and adhere. # DIRECTIONS FOR USE: FOR RUSTED SURFACES(To Remove Rust) 1.Remove any oil,grease,&dirt from surface.Remove loose rust with a wire brush. 2.Apply product to affected metal fll trength with a paintbrush,spray bottle or pump-up sprayer.Work the solution into rustedareas with a stiff briste brush and allow product to dry overnight to fully neutralize rust 3.Rinse or wipe surface with a damp cloth to remove any rust residue. 4.Paint treated surface within 48 hours of application to prevent formation of new rust.Two applications may be necessary to treatsevere rust. FOR TREATING METAL FOR PAINTING(Phosphotizing) 1.Remove any oil,grease,&dirt from surface. 2.Dilute 1 part product with 3 parts water in a plastic container. 3.Apply product with a paintbrush,spray botle or pump-up sprayer to metal.Surface may turn gray/white. 4.Thoroughly rinse with water after 15-30minutes. 5.Wipe off any loose powder that forms.Paint treated surface within 48 hours of application to preventformaton of new rust.FOR ETCHING CONCRETE(Before Applying a Coating) 1.Concrete must be clean and bare of sealers or coatings. 2.Dilute 1 part product into 4 parts water in a plastic container. 3.Apply this dilution evenly,at a rate of 300 sqft/gallon,using a plastic garden watering can with sprinkling head.Do not pour ontoone spot and brush out over surface.Product should begin foaming as it reacts with concrete -if no foaming happens concrete issealed and sealer mustbe removed. 4.Let stand at least 10 minutes and then thoroughly rinse with plenty of clean water,scrubbing lightly with a nylon broom to removeany residue.Allow surface to dry before top coating. IMPORTANT:Carefuly readall directions and cautions prior to use.Only use this product as directed on the label.Do notuse forany other purpose and do not mix with any other product such as bleach.Protect hands with chemical-resistant gloves and eyes withchemical splash goggles.Avoid contact with painted surfaces.Avoid ovrspray.Rinse tools with water after use. DANGER:MAY CAUSE BURNS.SKIN AND EYE IRRITANT.HARMFULIF SWALLOWED.Contains Phosphoric Acid.Avoid contact witheyes,skin and mucous membranes.Use with adequate ventilation.If breathing difficulty occurs,move to fresh air.Do not take internally.FIRST AID-IF SWALLOWED,do not induce vomiting.Drink 1 or 2 glasses of water and call physician immediately.IN CASE OF EYECONTACT,immediatelyflush with water,remove any contactlens and flush with water for at least 15minutes,then getimmediate medicalttention.FOR SKIN CONTACT,immediately wash with soap and water.Remove contaminated clothing and wash before reuse.If symptomspersist,get medical attention. KEEP OUT OF REACH OF CHILDREN.

FAQs

What does Klean-Strip Concrete and Metal Prep do?

It removes rust from iron and steel, treats metal surfaces to help paint adhesion, and etches concrete so coatings and stains can penetrate and adhere.

How should rusted metal surfaces be prepared and treated?

Remove oil, grease, and dirt, loosen rust with a wire brush, apply the product to the affected metal, work it in, let it dry overnight, then rinse or wipe to remove residue. Paint treated surface within 48 hours.

What safety precautions and first aid steps are recommended?

Wear chemical-resistant gloves and splash goggles, use adequate ventilation, avoid eye/skin contact, and protect painted surfaces from overspray. If swallowed, do not induce vomiting and call a physician; for eye contact flush for at least 15 minutes and get immediate medical attention; for skin contact wash with soap and water and seek care if symptoms persist.

Sep 27, 2026

Uploaded by Indoniesian Boy