ISO 3888-2:2011 - Passenger cars - Test track for a severe lane-change manoeuvre - Part 2 - Obstacle avoidance

Sep 18, 2026

Uploaded by Mack Lee

ISO 3888-2:2011 defines the test track requirements for passenger cars performing a severe lane-change manoeuvre, focusing on obstacle avoidance. The standard establishes the scope and provides normative references and key terms, then specifies track dimensions and the marking of the obstacle avoidance track. An informative annex outlines the test method. The document is presented as an ISO copyright-protected standard with publication details and foreword describing ISO drafting and committee processes.

LanguageEnglish

CategoryResearch & Report

FormatPDF

Pages9

Reading Time23 min

AccessFree to download

Contents Page

Foreword

Introduction

1 Scope

2 Normative references

3 Terms and definitions

4 Specifications

4.1 Dimensions of the obstacle avoidance track

4.2 Marking of the obstacle avoidance track

Annex A (informative) Test method

INTERNATIONAL STANDARD ISO 3888-2 Second edition 2011-03-15 Passenger cars—Test track for a severe lane-change manoeuvre— Part 2: Obstacle avoidance Voitures particulières—Piste d'essai de déboîtement latéral brusque— iTeh STarNtieD2:ÉAvitRemDent dP'obRstaEcleVIEW ( [standards.iteh.ai](standards.iteh.ai)) ISO 3888-2:2011 [https://standards.iteh.ai/catalog/standards/sist/e0dedc5d-b4b0-4f35-aee0-](https://standards.iteh.ai/catalog/standards/sist/e0dedc5d-b4b0-4f35-aee0-) 88a100611ddf/iso-3888-2-2011 Reference number ISO 3888-2:2011(E) ISO 3888-2:2011(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. iTeh STANDARD PREVIEW ( [standards.iteh.ai](standards.iteh.ai)) ISO 3888-2:2011 [https://standards.iteh.ai/catalog/standards/sist/e0dedc5d-b4b0-4f35-aee0-](https://standards.iteh.ai/catalog/standards/sist/e0dedc5d-b4b0-4f35-aee0-) 88a100611ddf/iso-3888-2-2011 COPYRIGHT PROTECTED DOCUMENT © ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [copyright@iso.org](copyright@iso.org) Web [www.iso.org](www.iso.org)[ ](www.iso.org)Published in Switzerland ii © ISO 2011 – All rights reserved ISO 3888-2:2011(E) Contents Page Foreword ............................................................................................................................................................ iv Introduction......................................................................................................................................................... v 1 Scope ...................................................................................................................................................... 1 2 Normative references............................................................................................................................ 1 3 Terms and definitions ........................................................................................................................... 1 4 Specifications ........................................................................................................................................ 1 4.1 Dimensions of the obstacle avoidance track ..................................................................................... 1 4.2 Marking of the obstacle avoidance track ............................................................................................2 Annex A (informative) Test method ..................................................................................................................4 iTeh STANDARD PREVIEW ( [standards.iteh.ai](standards.iteh.ai)) ISO 3888-2:2011 [https://standards.iteh.ai/catalog/standards/sist/e0dedc5d-b4b0-4f35-aee0-](https://stan

FAQs

What is ISO 3888-2:2011 about?

ISO 3888-2:2011 specifies the test track for a severe lane-change manoeuvre on passenger cars, with a focus on obstacle avoidance.

Which track elements does the standard specify?

It specifies the dimensions of the obstacle avoidance track and the marking of that track.

Where can the test method be found?

The test method is provided in Annex A, which is marked as informative.

Sep 18, 2026

Uploaded by Mack Lee

ISO 3888-2:2011 - Passenger cars - Test track for a severe lane-change manoeuvre - Part 2 - Obstacle avoidance_Page 1

Open in WPS to view all 9 pages