imc C1-1-LEMO(-VEAM)-FD - Manual - Edition 12-2025-11-06

Sep 30, 2026

Upload by Ezra

User documentation for the imc C1-1-LEMO(-VEAM)-FD device/module providing essential notes for safe installation and operation. Covers liability disclaimer, copyright, and requirements to use the accompanying software only under the imc Software License Agreement. Includes open source licensing information for components under GPL and guidance where to find the license list and request GPL sources. Explains that device instructions are hardware-focused, not software operation, and emphasizes adherence to safety regulations and compliance with specifications.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages92

Reading Time3 h 52 min

AccessFree to download

Table of contents

1 General introduction

2 Safety

3 Assembly and connection

imc C1-1-LEMO(-VEAM)-FD Manual Edition 12-2025-11-06 © 2025 imc Test & Measurement GmbH imc Test & Measurement GmbH •Voltastr. 5 • 13355 Berlin •Germany Disclaimer of liability The contents of this documentation have been carefully checked for consistency with the hardware and software systems described. Nevertheless, it is impossible to completely rule out inconsistencies, so that we decline to offer any guarantee of total conformity. We reserve the right to make technical modifications of the systems. Copyright © 2025 imc Test & Measurement GmbH, Germany This documentation is the intellectual property of imc Test & Measurement GmbH. imc Test & Measurement GmbH reserves all rights to this documentation. The applicable provisions are stipulated in the "imc Software License Agreement". The software described in this document may only be used in accordance with the provisions of the "imc Software License Agreement". Open Source Software Licenses Some components of imc products use software which is licensed under the GNU General Public License (GPL). Details are available in the About dialog. A list of the open source software licenses for the imc measurement devices is located on the imc STUDIO/imc WAVE/imc STUDIO Monitor installation medium in the folder "Products\imc DEVICES\OSS" or"Products\imc DEVICEcore\OSS" or "Products\imc STUDIO\OSS". If you wish to receive a copy of the GPL sources used, please contact our tech support. © 2025 imc Test & Measurement GmbH imc C1-1-LEMO(-VEAM)-FD-Manual, Edition 12-2025-11-06 Page 2 Notes regarding this document This document provides important notes on using the device / the module. Safe working is conditional on compliance with all safety measures and instructions provided. The manual is to be used as a kind of reference book. You can skip the description of the modules you do not have. Additionally, all accident prevention and general safety regulations pertinent to the location at which the device is used must be adhered to. These instructions exclusively describe the device, not how to operate it by means of the software! If you have any questions as to whether you can set up the device / module in the intended environment, please contact our tech support. The measurement system has been designed, manufactured and unit-tested with all due care and in accordance with the safety regulations before delivery and has left the factory in perfect condition. In order to maintain this condition and to ensure safe operation, the user must observe the notes and warnings contained in this chapter and in the specific sections applicable to the concrete device. Never use the device outside the specification. This will protect you and prevent damage to the device. Training programs for introduction to the systems, and advanced workshops We recommend that before you begin working with the device / the module you participate in an extensive training session. Such training will enable you to get started working efficiently much faster. Additionally, you will obtain valuable tips and information on how to use the software more effectively. More information is available on our homepage under "Service & Training" > "imc ACADEMY". Special notes Warning Warnings contain information that must be observed to protect the user from harm or to prevent damage to property. Note Notes denote useful additional information on a particular topic. © 2025 imc Test & Measurement GmbH imc C1-1-LEMO(-VEAM)-FD-Manual, Edition 12-2025-11-06 Page 3 Table of contents 1 General introduction ................................................................................................. 6 1.1 Tech support ................................................................................................................................... 6 1.2 Service and maintenance ............................................................................................

FAQs

What safety requirements must be followed when using the device or module?

Safe working is conditional on compliance with all safety measures and instructions provided. Users must also adhere to accident prevention and general safety regulations applicable at the installation location and never use the device outside its specification.

Does the manual explain how to operate the device via software?

The instructions exclusively describe the device, not how to operate it through software. If there is uncertainty about the intended environment, users should contact tech support.

Where can the list of open source software licenses be found and how can GPL sources be requested?

The list is located on the installation medium in the imc STUDIO/imc WAVE/imc STUDIO Monitor folders under Products\imc DEVICES\OSS, Products\imc DEVICEcore\OSS, or Products\imc STUDIO\OSS. To receive GPL source copies, contact tech support.

Sep 30, 2026

Upload by Ezra