Graphic Operation Terminal (GOT2000 Series) - Basic Training Textbook - Safety Precautions

Sep 26, 2026

Training safety precautions for using the Graphic Operation Terminal (GOT2000 Series) with GT Works3. The document instructs trainees to review relevant manuals when designing and handling systems, follow instructor guidance, and avoid unsafe actions such as touching terminal blocks during power supply. It explains safe procedures when opening safety covers, installing or removing units, and stopping the machine via Power Switch or Emergency Switch if unusual odours or sounds occur. It also specifies immediate reporting of any troubles.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages254

Reading Time10 h 40 min

AccessFree to download

SAFETY PRECAUTIONS

Precautions during training

REVISIONS

Graphic Operation Terminal (GOT2000 Series) Basic Training Textbook (for GT Works3) SAFETY PRECAUTIONS (Make sure to read before training) When designing a system, always read the relevant manuals and give due consideration to safety. In addition, pay careful attention to the following points for proper handling during training. [Precautions during training] | Danger | | --- | | ● To prevent electric shock, do not touch the terminal block while the power is supplied.
● When opening the safety cover, turn off the power, or make sure that it is sufficiently safe. | | Caution | | --- | | ● Follow the instructor's directions during training.
● Do not remove training machine units or change wiring without permission.
Doing so could cause a breakdown, faulty operation, injury, or fire.
● Turn the power OFF before mounting or removing a unit.
Doing so while the current is ON could cause a breakdown or electric shock.
● If the training machine emits a strange odour or sound, press the "Power Switch" or the "Emergency Switch" to stop the machine.
● If any trouble occurs, contact the instructor right away. | REVISIONS * The textbook number is given on the bottom left of the back cover. | Print Date | * Textbook Number | | Revision | | --- | --- | --- | --- | | February 2018 | SH(NA)-081926ENG-A | First printing | | | | | | | This textbook confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this textbook. 􀂤2018 MITSUBISHI ELECTRIC CORPORATION SAFETY PRECAUTIONS ............................................................. A-1 REVISIONS ....................................................................... A-3 CONTENTS ....................................................................... A-5 Introduction ........................................................................ A-8 Relevant manuals ................................................................... A-9 Copyright notice .................................................................... A-9 System configuration in this textbook ...................................................A-10 1. What is the GOT? | 1.1 About the GOT................................................................. 1-1
1.2 Procedures for monitoring the PLC CPU by GOT ...................................... 1-2
1.3 GOT2000 series features ........................................................ 1-3
1.4 GOT function list ............................................................... 1-4
1.5 Equipment required for using GOT ................................................ 1-10
1.6 Applicable connection type between the GOT and the PLC CPU ......................... 1-18
1.7 Connection to equipment other than the PLC ........................................ 1-21
1.8 Multi-channel function .......................................................... 1-22
2. GOT operation | | --- | | 2. 1 Summary of operation 2-1
3. About GT Designer3 | | 3.1 About GT Designer3 ............................................................ 3-1
3.2 GT Designer3 screen configuration and features ...................................... 3-2
3.2.1 Screen layout of GT Designer3 .............................................. 3-2
3.2.2 Features of GT Designer3 .................................................. 3-4
3.3 How to use Help ............................................................... 3-9
3.3.1 Displaying Help ........................................................... 3-9
3.3.2 Using Help .............................................................. 3-9
4. From GOT screen creation up to the test | 4.1 Preparation before using the GOT.........................................

FAQs

What should trainees do before and during system training?

Read the relevant manuals and consider safety requirements when designing and handling systems. Follow instructor directions during training.

What is prohibited to prevent electric shock during training?

Do not touch the terminal block while power is supplied. Turn off power or ensure sufficient safety before opening the safety cover.

How should trainees respond if the training machine emits a strange odour or sound?

Press the "Power Switch" or the "Emergency Switch" to stop the machine, then contact the instructor right away if trouble occurs.

Sep 26, 2026

Upload by Anna Hans