Freedom Hydro-40 - Preliminary Hoistway & Electrical Notes - Drawing Approval

Oct 28, 2026

Preliminary drawing notes for the Freedom Hydro-40 lift define hoistway, finished runway, and controller dimensions, referencing drywall and code clearances (e.g., 36 in min and CSA/ASME A17.1-related limits). The document specifies owner/agent responsibilities for level/plumb/square construction, masonry/carpentry/drywall work, and providing suitable door lintels while confirming code compliance. It also outlines provisions by others for machine room access, alignment of entrance assemblies and doors, and electrical requirements including power supply, disconnects, conductor protection, and lighting levels in machine rooms.

LanguageEnglish

CategoryResearch & Report

FormatPDF

Pages3

Reading Time8 min

AccessFree to download

Provisions by Owner/Agent

Hoistway and Finished Runway Notes

Doors, Clearances, and Door Alignment

Structural and Building Responsibility

Provisions by Others

Machine Room Location and Access

Electrical: Power Supply, Disconnects, and Lighting

CONTROL VALVE PLEASE NDTE: -HYDRAULIC LINE 625/8” DVERALL HOISTWAY LENGTH AND FINISHED RUNWAY- CONTROLLER LENGTH WIDTH DIMENSIONS ARE FROM DRYWALL NEC 36”MIN. 573/8” CEC 1m(39”)MIN. TO DRYWALL(WHERE APPLICABLE) □VERALL CAB- 1” LENGTH -CAB WITH LIGHT SCREEN 41/4” LIFT PLATFORM CLEARANCE 占也 54” CLEAR CAB- JACK UNIT DEPTH 口 265/8”DBG- CRAIL BRKT 4JACK 3/8” 10 1/2” M/R PLAN AT LOWER LEVEL 5” o0 0 PRELIMINARY DRAWING □NLY 33 1/44十 DRAWING APPROVAL: SEE NOTE [2] THIS DRAWING REFLECTS DUR INTERPRETATIDN DF THE INFORMATIDN PROVIDED BY THE DEALER DN_THE DRDER FDRM.THIS INFDRMATIDN IS THE ? CLEAR INSIDE3 ENARTNE4 DEALER'S RESPDNSIBILITY,AND IS THE BASIS FROM_WHICH THIS LIFT IS DESIGNED AND MANUEACTURED.PLEASE INDICATE THE REQUESTED ACTION BY CHECKING DNE DF THE FOLLOVING BDXES AND SIGNING BELDV TD 40 CAB AUTHDRIZE CDMPLETIDN F THIS DRDER. APPROVED WITH NO EXCEPTIONS MANUFACTURE PRDDUCT AS PER DRAWING □APPRDVED WITH EXCEPTIDNS,ND REAPPRDVAL REQUIRED B-B MAKE CHANGES AS NOTED,NO REAPPRDVAL DRAWING REQUIRED CHANGE AS NOTED,REAPPROVAL REQUIRED 2 MAKE CHANGES AS NDTED,SEND CDRRECTED DRAWING FDR REAPPRDVAL BEFDRE MANUFACTURE SIGNATUREL_ DATE:_ CHANGES REQUESTI 2. 3. ù- 4. CAUTIDN DNCE THE DRAVING IS APPRDVED,JDB CANCELLATIDN FEES WLL APPLY | | | OFFICE USE ONLY: | | Part No. | | --- | --- | --- | --- | --- | | | | 0.0
COMFIGURATON VERSION STAMP: | | | | | | | | Voriont No. .
46 | | | | M0UE VERSON STAMP:
I-S-6.33 | | | | | CUSTOMER:
工 | | B6716/15 | INationwideLifts
www.elevators.com | | PLAN VIEW | PROJECT:
Freedom Hydro-40
wide × 54 deep | | EMSON DATE
06/16/15 | | | | ADDRESS:
Side, Rails
Doors Same
On Left
info@elevators.com
888-323-8755 | | COMPLETED BY:
ondrdoneblifts | | | | | | 3 | JOB No D-0000001 □F 3 | | | | OFFICE USE ONLY: | | Part No. | | | --- | --- | --- | --- | --- | --- | | | | 0.0
COMFGCJRATION VESON STAMP: | | | | | | | | | variant No.48546 | | | | | I-S-6.33
WOUE ESON STAMP: | | | | | | | | | lINationwideLifts
www.elevators.com
◎ Savaria. | | | ELEVATIDN VIEW B-B | 工F
TI□NW工D
S
aJreedom Hydro
40 wide
×
54
deep | | DATE:
06/16/15
EMSON DATE:
06/16/15 | | | | | ADDRESS:
Doors Same Side,Rails on Left
888-323-8755
info@elevators.com | | COMPLETED BY:
onybrneluift | | | | | | | S | JOB No.
P-00000020F3 | | s | PROVISIONS BY □THERS
米GENERAL
HOISTWAY-THE HOISTWAY MUST BE IN ACCDRDANCE WITH NATIONAL
US/ASME(SEE APPLIED CDDE),ALL STATE AND LDCAL CDDES.
PLUMB HDISTWAY-DUE TD CLOSE RUNNING CLEARANCES □WNER/AGENT
MUST ENSURE THAT HOISTWAY AND PIT(WHERE PROVIDED)ARE
LEVEL,PLUMB AND SQUARE AND ARE IN ACCDRDANCE WITH THE
DIMENSIONS ON THESE DRAWINGS.
MINIMUM OVERHEAD CLEARANCE-□WNER/AGENT MUST ENSURE MINIMUM
□VERHEAD CLEARANCE IS IN CDMPLIANCE WITH CODES.
CDNSTRUCTIDN SITE-□WNER/AGENT TO PROVIDE ALL MASDNRY,
CARPENTRY AND DRYWALL WDRK AS REQUIRED AND SHALL PATCH AND
MAKE GDOD(INCLUDING FINISH PAINTING)ALL AREAS WHERE
WALLS/FLOORS MAY REQUIRE_TOBE CUT,DRILLED OR ALTERED IN
ANY WAY TO PERMIT THE PROPER INSTALLATION OF THE LIFT.
DIMENSIDNS
CDNTRACTOR/CUSTOMER TO VERIFY ALL DIMENSIONS AND REPORT ANY
DISCREPANCIES TO □UR OFFICE IMMEDIATELY.
米STRUCTURAL
FLDOR/SUPPORT WALL LDADS-CDNTRACTOR TO ASSURE
THAT BUILDING AND SHAFT WILL SAFELY SUPPORT ALL LOADS
IMPOSED BY THE LIFT EQUIPMENT.REFER TO THE TABLES ON THIS
DRAWING FOR LDADS IMPOSED BY THE EQUIPMENT.
DDDRS-SUITABLE LINTELS MUST BE PROVIDED BY □WNER/AGENT.
DDOR_FRAMES ARE NOT DESIGNED_TD SUPPORT OVERHEAD_WALL LDADS.
ALL FULL HEIGHT DODRS MUST BE AL

FAQs

What are the key hoistway and runway responsibilities for the owner/agent?

The owner/agent must ensure the hoistway and pit (if provided) are level, plumb, and square, and that finished runway clearances comply with applicable codes. The document also requires compliance with minimum overhead clearance requirements.

What door and clearance constraints are specified?

Suitable lintels must be provided by the owner/agent, and door frames are not designed to support overhead wall loads. The notes also include maximum clearances from the door sill to the hoistway door and limits for the elevator car door to hoistway door to comply with CSA/ASME A17.1.

What electrical requirements are given for the lift system?

The document calls for a lockable fused disconnect with auxiliary contact to brake the battery feed, and specifies use of circuit breakers with a 3-pole breaker for battery feed as required. It also states machine room illumination must be not less than 200 lx (19 FC) at the floor level.

Oct 28, 2026

Upload by Jordan Avery