FoamLogixTM Model 2.1A and 1.7AHP Class “A” Electronic Foam Proportioning Systems - Description, Installation and Operation Manual

Nov 4, 2026

Manual for the Hale FoamLogixTM Class “A” electronic foam proportioning systems, covering model 2.1A and 1.7AHP. Provides apparatus information, manual part number, revision history, and calibration factor references. Includes safety instructions for installers and service personnel, followed by system description, OEM installation and initial setup, setup and calibration for start-up, operational guidance for maintenance, troubleshooting procedures, and parts identification for commonly used components. Emphasizes proper operation and preventive maintenance.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages96

Reading Time4 h 2 min

AccessFree to download

HOW TO USE THIS MANUAL

SECTION 1 SAFETY

SECTION 2 DESCRIPTION

SECTION 3 INSTALLATION

SECTION 4 SETUP AND CALIBRATION

SECTION 5 OPERATION

SECTION 6 TROUBLESHOOTING

SECTION 7 PARTS IDENTIFICATION

FoamLogixTM Model 2.1A and 1.7AHP Class “A”Electronic Foam Proportioning Systems Description, Installation and Operation Manual HALE PRODUCTS INC. 700 Spring Mill Avenue Conshohocken, PA 19428 Telephone: 610-825-6300 Fax: 610-825-6440 CLASS 1 607 NW 27th Avenue ● Ocala, FL 34475 U.S.A. Telephone: 352-629-5020 FAX: 800-533-3569 GODIVA LTD. Charles Street ● Warwick, England CV34 5LR Phone: 44-1-926-623600 IDEX DINGLEE TECHNOLOGY (Tianjin) Co. Ltd. No.9, 2nd Haitai Fazhan Road Huayuan Industrial Development Area (outside of ring road) Tianjin High-Tech Industrial Park Tianjin China Telephone: 011-86-22-8568-9800 FAX: 011-862285689808 Manual p/n: 029-0020-74-0-E APPARATUS INFORMATION Hale FoamLogix System Serial Number In Service Date Fire Department Engine Number Calibration Factors: Water Flow Factor Class A Foam Factor NOTICE! Hale Products does not assume responsibility for product failure resulting from improper maintenance or operation. Hale Products is responsible only to the limits stated in the product warranty. Product specifications contained in this manual are subject to change without notice. All Hale products are quality components--ruggedly designed, accurately machined, precision inspected, carefully assembled and thoroughly tested. In order to maintain the high quality of your unit, and to keep it in a ready condition, it is important to follow the instructions on care and operation. Proper use and good preventive maintenance will lengthen the life of your unit. ALWAYS INCLUDE THE UNIT SERIAL NUMBER IN YOUR CORRESPONDENCE. | ECO NO | REV | CHANGED FROM | BY | DATE | APVD | | --- | --- | --- | --- | --- | --- | | 03-110 | A | RELEASED FOR PRINTING | PRW | 6/1/2003 | MAL | | 03-215 | B | UPDATED FOR DESIGN CHANGE | PRW | 6/30/2003 | MAL | | 04-236 | C | UPDATE FOR DESIGN CHANGE | LWH | 10/05/04 | MAL | | ECR 2743 | D | UPDATE TO INCLUDE 1.7ahp | RLL | 1/15/09 | DC | | | E | CHANGE INFO ON FOAM FLOW SENSOR REPLACEMENT | RLL | 8/10/09 | DC | Manual P/N: 029-0020-74-0, Rev E HOW TO USE THIS MANUAL This manual is divided into seven sections for clarity and ease of use. Each of the following manual sections can be a stand alone section or can be used in conjunction with each other. SECTION 1 SAFETY This section must be carefully read, understood and adhered to strictly by all installer/builders, operators and service personnel using the Hale FoamLogix 2. 1A and 1.7AHP Foam Proportioning Systems. Do not use or install the system until you have thoroughly read this section. Failure to comply could cause risk of serious injury to yourself and others, or damage to the system. SECTION 2 DESCRIPTION Provides an introduction to the Hale foam proportioning system along with guidelines for designing and ordering a complete system. SECTION 3 INSTALLATION Provides information to assist the OEM with installation and initial setup of Hale foam proportioning systemson an apparatus. SECTION 4 SETUP AND CALIBRATION Is used by the installer and end user for start-up and calibration of the Hale foam proportioning system. SECTION 5 OPERATION Is primarily used by the apparatus user for proper operation and maintenance of the Hale foam proportioning system. SECTION 6 TROUBLESHOOTING If a problem developes, see this section for troubleshooting procedures. SECTION 7 PARTS IDENTIFICATION Section 7 includes a parts breakdown of the most commonly used parts of the FoamLogix System. NOTES CONTENTS PAGE HOW TO USE THIS MANUAL ........................................................................................3 SECTION 1 SAFETY.................................................................................................................................... 3 SECTION 2 DESCRIPTION ........................................................................................................................ 3 SECTION 3 INSTALLATION ...............

FAQs

What models are covered by this FoamLogix manual?

The manual covers the Hale FoamLogixTM Model 2.1A and 1.7AHP Class “A” Electronic Foam Proportioning Systems.

What safety guidance does the manual require before using the system?

SECTION 1 SAFETY must be carefully read, understood, and strictly adhered to by installer/builders, operators, and service personnel before use or installation. Noncompliance can lead to serious injury risk and system damage.

Where can the user find setup, calibration, and troubleshooting instructions?

Setup and calibration are provided in SECTION 4. Troubleshooting procedures are provided in SECTION 6.

Nov 4, 2026

Uploaded by WPS_1786070896