Flex 6EX2 System - Radio Control Equipment Instruction Manual - Part Number 191-50600-M000F R00 - November 2017

Oct 23, 2026

Upload by Jiven

Instruction manual for the Magnetek Flex 6EX2 radio control system used with material handling cranes. Covers service information, product safety guidance, and radio-controlled safety requirements including installation considerations, authorized operator training, transmitter and receiver overview, and pre-operation testing. Provides detailed configuration instructions for transmitter and receiver functions such as firmware version, channel and pairing setup, i-chip features, timers, output power, infrared programming, and feedback settings, plus receiver relay, dipswitch, jumper, fuse, and indicator installation.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages45

Reading Time1 h 53 min

AccessFree to download

Service Information

Product Manual Safety Information

1 Introduction

2 Radio Controlled Safety

2.1 Critical Installation Considerations

2.2 General

2.3 Persons Authorized to Operate Radio Controlled Cranes

2.4 Safety Information and Recommended Training for Radio Controlled Equipment Operators

2.5 Transmitter Unit

2.6 Pre-Operation Test

2.7 Batteries

3 General System Information

3.1 Transmitter

3.2 Receiver

4 Function Settings

4.1 Transmitter

4.2 Receiver

Flex 6EX2 System Radio Control Equipment Instruction Manual Part Number: 191-50600-M000F R00 November 2017 ©Copyright 2017 Magnetek Material Handling Distributed by Tri-State Equipment Company Inc. [sales@tsoverheadcrane.com](sales@tsoverheadcrane.com) [www.tsoverheadcrane.com](www.tsoverheadcrane.com) [Tel:](Tel:) (314) 869-7200 Page Intentionally Left Blank Flex 6EX2 Instruction Manual November 2017 Table of Contents Service Information ............................................................................................................................ 5 Product Manual Safety Information .................................................................................................. 6 1 Introduction......................................................................................................................................... 7 2 Radio Controlled Safety ..................................................................................................................... 8 2.1 Critical Installation Considerations ............................................................................................... 9 2.2 General......................................................................................................................................... 9 2.3 Persons Authorized to Operate Radio Controlled Cranes............................................................ 9 2.4 Safety Information and Recommended Training for Radio Controlled Equipment Operators.... 10 2.5 Transmitter Unit.......................................................................................................................... 11 2.6 Pre-Operation Test..................................................................................................................... 11 2.7 Batteries ..................................................................................................................................... 11 3 General System Information............................................................................................................ 12 3.1 Transmitter ................................................................................................................................. 12 3.1.1 External Illustration ................................................................................................................ 12 3.1.2 Internal Illustration ................................................................................................................. 13 3.2 Receiver ..................................................................................................................................... 14 3.2.1 External Illustration ................................................................................................................ 14 3.2.2 Internal Illustration ................................................................................................................. 15 4 Function Settings ............................................................................................................................. 16 4.1 Transmitter ................................................................................................................................. 16 4.1.1 Transmitter Firmware Version ............................................................................................... 16 4.1.2 Transmitter Channel Settings ................................................................................................ 16 4.1.3 Remote Pairing ...................................................................................................................... 18 4.1.4 I-Chip ..................................................................................................................................... 19 4.1.5 Transmitter Start Function Settings ............................................................

FAQs

What safety requirements are emphasized before using the Flex 6EX2 radio control system?

The manual highlights radio-controlled safety, including critical installation considerations, general safety guidance, and recommended training for equipment operators. It also covers authorized persons for operating radio controlled cranes and pre-operation testing steps.

How are transmitter functions configured on the Flex 6EX2 system?

Transmitter settings include firmware version, channel settings, remote pairing, i-chip configuration, start function settings, inactivity timer settings, output power settings, infrared programming, pushbutton function settings, frequency band display, output feedback settings, and zero-G sensor settings.

What receiver configuration options are covered in the manual?

Receiver setup includes channel settings, output relay configurations, dipswitch and jumper settings, fuse ratings, and installation of the indicator light and buzzer.

Oct 23, 2026

Upload by Jiven