FANUC Series 0+-MODEL F - Operation and Maintenance Handbook

Oct 25, 2026

Manual providing operational guidance and safety precautions for FANUC Series 0+-MODEL F CNC units. It defines Warning, Caution, and Note classifications and explains how to safely operate machines by verifying correct machine behavior, entered data, feedrate suitability, and tool compensation settings. It also covers user responsibilities to follow machine-tool-builder documentation, proper handling after power-on, and cautions about modifying factory-set CNC/PMC parameters. Includes export control and trademark notices.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages822

Reading Time34 h 31 min

AccessFree to download

Safety Precautions

Definition of Warning, Caution, and Note

General Warnings and Cautions

FANUC Series 0+-MODEL F OPERATION AND MAINTENANCE HANDBOOK B-64607EN/01 • No part of this manual may be reproduced in any form. • All specifications and designs are subject to change without notice. The products in this manual are controlled based on Japan’s“Foreign Exchange and Foreign Trade Law”. The export of Series 30i-B, Series 31i-B5 from Japan is subject to an export license by the government of Japan. Other models in this manual may also be subject to export controls. Further, re-export to another country may be subject to the license of the government of the country from where the product is re-exported. Furthermore, the product may also be controlled by re-export regulations of the United States government. Should you wish to export or re-export these products, please contact FANUC for advice. The products in this manual are manufactured under strict quality control. However, when some serious accidents or losses are predicted due to a failure of the product, make adequate consideration for safety. In this manual we have tried as much as possible to describe all the various matters. However, we cannot describe all the matters which must not be done, or which cannot be done, because there are so many possibilities. Therefore, matters which are not especially described as possible in this manual should be regarded as ”impossible”. This manual contains the program names or device names of other companies, some of which are registered trademarks of respective owners. However, these names are not followed by ® or ™ in the main body. SAFETY PRECAUTIONS This section describes the safety precautions related to the use of CNC units. It is essential that these precautions be observed by users to ensure the safe operation of machines equipped with a CNC unit (all descriptions in this section assume this configuration) . Note that some precautions are related only to specific functions, and thus may not be applicable to certain CNC units. Users must also observe the safety precautions related to the machine, as described in the relevant manual supplied by the machine tool builder. Before attempting to operate the machine or create a program to control the operation of the machine, the operator must become fully familiar with the contents of this manual and relevant manual supplied by the machine tool builder. DEFINITION OF WARNING, CAUTION, AND NOTE This manual includes safety precautions for protecting the user and preventing damage to the machine. Precautions are classified into Warning and Caution according to their bearing on safety. Also, supplementary information is described as a Note. Read the Warning, Caution, and Note thoroughly before attempting to use the machine. WARNING Applied when there is a danger of the user being injured or when there is a danger of both the user being injured and the equipment being damaged if the approved procedure is not observed. CAUTION Applied when there is a danger of the equipment being damaged, if the approved procedure is not observed. NOTE The Note is used to indicate supplementary information other than Warning and Caution. • Read this manual carefully, and store it in a safe place. SAFETY PRECAUTIONS GENERAL WARNINGS AND CAUTIONS WARNING 1 Never attempt to machine a workpiece without first checking the operation of the machine. Before starting a production run, ensure that the machine is operating correctly by performing a trial run using, for example, the single block, feedrate override, or machine lock function or by operating the machine with neither a tool nor workpiece mounted. Failure to confirm the correct operation of the machine may result in the machine behaving unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user. 2 Before operating the machine, thoroughly check the entered data. Operating the machine with incorrectly specified data may result in the machine beh

FAQs

What is the difference between Warning, Caution, and Note in this manual?

Warning applies when there is danger of user injury, or both user injury and equipment damage. Caution applies when there is danger of equipment damage. Note provides supplementary information other than Warning and Caution.

Why is a trial run recommended before starting production?

A trial run using functions such as single block, feedrate override, or machine lock helps confirm the machine operates correctly. Failure to confirm correct operation may cause unexpected behavior, damage, or injury.

What precautions should be taken when switching on the power?

Immediately after switching on, do not touch keys on the MDI panel until the position display or alarm screen appears on the CNC unit. Some keys can trigger maintenance or special operations and may put the CNC unit in an abnormal state.

Oct 25, 2026

Upload by Margaret