FANUC Series 0* Mate - MODEL D - For Machining Center System USER'S MANUAL

Oct 25, 2026

Upload by Angel

FANUC Series 0* Mate - MODEL D for Machining Center System USER’S MANUAL provides safety precautions for using CNC units, emphasizing correct operation and preventing injury to users and damage to equipment. It defines Warning, Caution, and Note classifications and requires users to fully understand both this manual and the machine tool builder’s relevant manual before operating or creating control programs. It also covers general warnings for trial runs, verified input data, appropriate feedrate selection, tool compensation checks, careful parameter changes, and safe handling immediately after power-on.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages406

Reading Time17 h 3 min

AccessFree to download

SAFETY PRECAUTIONS

DEFINITION OF WARNING, CAUTION, AND NOTE

GENERAL WARNINGS AND CAUTIONS

WARNINGS AND CAUTIONS RELATED TO PROGRAMMING

WARNINGS AND CAUTIONS RELATED TO HANDLING

WARNINGS RELATED TO DAILY MAINTENANCE

FANUC Series 0*-MODEL D FANUC Series 0* Mate-MODEL D For Machining Center System USER’S MANUAL • No part of this manual may be reproduced in any form. • All specifications and designs are subject to change without notice. The products in this manual are controlled based on Japan’s “Foreign Exchange and Foreign Trade Law”. The export from Japan may be subject to an export license by the government of Japan. Further, re-export to another country may be subject to the license of the government of the country from where the product is re-exported. Furthermore, the product may also be controlled by re-export regulations of the United States government. Should you wish to export or re-export these products, please contact FANUC for advice. In this manual we have tried as much as possible to describe all the various matters. However, we cannot describe all the matters which must not be done, or which cannot be done, because there are so many possibilities. Therefore, matters which are not especially described as possible in this manual should be regarded as ”impossible”. This manual contains the program names or device names of other companies, some of which are registered trademarks of respective owners. However, these names are not followed by 􀂓 or 􀂕 in the main body. SAFETY PRECAUTIONS This section describes the safety precautions related to the use of CNC units. It is essential that these precautions be observed by users to ensure the safe operation of machines equipped with a CNC unit (all descriptionsin this section assume this configuration) . Note that some precautions are related only to specific functions, and thus may not be applicable to certain CNC units. Users must also observe the safety precautions related to the machine, as described in the relevant manual supplied by the machine tool builder. Before attempting to operate the machine or create a program to control the operation of the machine, the operator must become fully familiar with the contents of this manual and relevant manual supplied by the machine tool builder. CONTENTS DEFINITION OF WARNING, CAUTION, AND NOTE ................ s-2 GENERAL WARNINGS AND CAUTIONS.................................... s-3 WARNINGS AND CAUTIONS RELATED TO PROGRAMMING ............................................................................. s-6 WARNINGS AND CAUTIONS RELATED TO HANDLING........ s-8 WARNINGS RELATED TO DAILY MAINTENANCE............... s-11 DEFINITION OF WARNING, CAUTION, AND NOTE This manual includes safety precautions for protecting the user and preventing damage to the machine. Precautions are classified into Warning and Caution according to their bearing on safety. Also, supplementary information is described as a Note. Read the Warning, Caution, and Note thoroughly before attempting to use the machine. WARNING Applied when there is a danger of the user being injured or when there is a danger of both the user being injured and the equipment being damaged if the approved procedure is not observed. CAUTION Applied when there is a danger of the equipment being damaged, if the approved procedure is not observed. NOTE The Note is used to indicate supplementary information other than Warning and Caution. • Read this manual carefully, and store it in a safe place. GENERAL WARNINGS AND CAUTIONS WARNING 1 Never attempt to machine a workpiece without first checking the operation of the machine. Before starting a production run, ensure that the machine is operating correctly by performing a trial run using, for example, the single block, feedrate override, or machine lock function or by operating the machine with neither a tool nor workpiece mounted. Failure to confirm the correct operation of the machine may result in the machine behaving unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user. 2 Before operating the machine, thoroughly check the entered dat

FAQs

What do Warning, Caution, and Note mean in this manual?

Warning applies when there is a danger of user injury or injury plus equipment damage if approved procedures are not followed. Caution applies when there is a danger of equipment damage if procedures are not followed. Note provides supplementary information beyond Warning and Caution.

Why is a trial run required before production?

The manual requires checking the machine’s operation before machining a workpiece. A trial run helps ensure the machine operates correctly, preventing unexpected behavior that can damage the workpiece or machine and cause user injury.

What safety steps should be taken right after switching on power?

After power-on, the manual instructs not to touch keys on the MDI panel until the position display or alarm screen appears. Some keys are for maintenance or special operations and could place the CNC unit in an abnormal state.

Oct 25, 2026

Upload by Angel