FANUC Robot series R-30iB Mate/R-30iB Mate Plus Controller - Maintenance Manual

Oct 24, 2026

Upload by Hazel

Maintenance Manual for FANUC Robot series R-30iB Mate and R-30iB Mate Plus controller, covering proprietary information, publication revision and copyright notices, and guidance on how FANUC describes product systems such as robots, controllers, software, and related tools. Includes authorized-use restrictions, training requirements for installation, operation and maintenance, and safety/EMI warning regarding radiofrequency emissions. Provides contact channels for training, technical support, service, parts, and documentation feedback, plus trademark and patent information relevant to described products.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages334

Reading Time14 h 2 min

AccessFree to download

Copyrights and Trademarks

Proprietary Information and Use Restrictions

Training Requirements

Safety Warning (Radiofrequency Interference)

Customer Assistance and Documentation Feedback

Patents

FANUC Robot series R-30iB Mate/R-30iB Mate Plus CONTROLLER MAINTENANCE MANUAL MARETIBCN01121E REV. G ©2017 FANUC America Corporation All Rights Reserved. This publication contains proprietary information of FANUC America Corporation furnished for customer use only. No other uses are authorized without the express written permission of FANUC America Corporation. FANUC America Corporation 3900 W. Hamlin Road Rochester Hills, Michigan 48309–3253 B-83525EN/07 Copyrights and Trademarks This new publication contains proprietary information ofFANUC America Corporation furnished for customer use only. No other uses are authorized without the express written permission ofFANUC America Corporation. The descriptions and specifications contained in this manual were in effect at the time this manual was approved for printing. FANUC America Corporation, hereinafter referred to as FANUC, reserves the right to discontinue models at anytime or to change specifications or design without notice and without incurring obligations. FANUC manuals present descriptions, specifications, drawings, schematics, bills of material, parts, connections and/or procedures for installing, disassembling, connecting, operating and programming FANUC products and/or systems. Such systems consist of robots, extended axes, robot controllers, application software, the KAREL® programming language, INSIGHT® vision equipment, and special tools. FANUC recommends that only persons who have been trained in one or more approved FANUC Training Course(s) be permitted to install, operate, use, perform procedures on, repair, and/or maintain FANUC products and/or systems and their respective components. Approved training necessitates that the courses selected be relevant to the type of system installed and application performed at the customer site. WARNING This equipment generates, uses, and can radiate radiofrequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. As temporarily permitted by regulation, it has not been tested for compliance with the limits for Class A computing devices pursuant to Subpart J and Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of the equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measure may be required to correct the interference. FANUC conducts courses on its systems and products on a regularly scheduled basis at the company's world headquarters in Rochester Hills, Michigan. For additional information contact FANUC America Corporation Training Department 3900 W. Hamlin Road Rochester Hills, Michigan 48309-3253 [www.fanucamerica.com](www.fanucamerica.com) For customer assistance, including Technical Support, Service, Parts & Part Repair, and Marketing Requests, contact the Customer Resource Center, 24 hours a day, at 1-800-47-ROBOT (1-800-477-6268) . International customers should call 011-1-248-377-7159. Send your comments and suggestions about this manual to: [product.documentation@fanucamerica.com](product.documentation@fanucamerica.com) Copyright © 2017 by FANUC America Corporation All Rights Reserved The information illustrated or contained herein is not to be reproduced, copied, downloaded, translated into another language, published in any physical or electronic format, including internet, or transmitted in whole or in part in any way without the prior written consent ofFANUC America Corporation. AccuStat®, ArcTool®, iRVision®, KAREL®, PaintTool®, PalletTool®, SOCKETS®, SpotTool®, SpotWorks®, and TorchMate® are Registered Trademarks ofFANUC. FANUC reserves all proprietary rights, including but not limited to trademark and trade name rights, in the following names: AccuAir™, AccuCal™, AccuChop™, AccuFlow™, AccuPath™, AccuSeal™, ARC Mate™, A

FAQs

What restrictions apply to using the manual’s information?

The manual contains proprietary information furnished for customer use only. Other uses are not authorized without express written permission from FANUC America Corporation.

Who is allowed to install, operate, and maintain FANUC products?

Only persons trained in one or more approved FANUC Training Course(s) relevant to the installed system and customer application should perform installation, operation, repair, and maintenance procedures.

What safety warning is included regarding radiofrequency energy?

The equipment can generate and radiate radiofrequency energy and may cause interference if not installed and used according to the manual. Operation in residential areas is likely to cause interference, requiring the user to correct it at their own expense.

Oct 24, 2026

Upload by Hazel