F1 in SchoolsTM Design Project with SolidWorks® Software - For Type-R Cars - Notices and Table of Contents

Oct 23, 2026

Upload by Jake

Engineering Design and Technology Series material outlining the F1 in SchoolsTM Design Project using SolidWorks® software for Type-R cars. The document provides company and licensing notices for Dassault Systèmes SolidWorks Corporation, including changes without notice, reproduction restrictions, and warranty and license terms. It lists patent notices, trademarks, and other legal acknowledgements, followed by SolidWorks copyright notices. A table of contents section introduces the book’s structure, including usage guidance, SolidWorks basics, prerequisites, and early steps for starting the software and opening an existing part.

LanguageEnglish

CategoryResearch & Report

FormatPDF

Pages176

Reading Time7 h 24 min

AccessFree to download

Introduction

Using This Book

What is SolidWorks Software?

Prerequisites

Conventions Used in This Book

Before You Begin

Add the Folder to the Design Library Path

Designing the Race Car

Important Design Considerations

About Balsa

Start SolidWorks and open an existing part

Engineering Design and Technology Series F1 in SchoolsTM Design Project with SolidWorks® Software For Type-R Cars Dassault Systèmes SolidWorks Corp. 300 Baker Avenue Concord, MA 01742 USA Phone: 1 800693 9000 Outside the US: 1 978 371 5011 Fax: 1 978 371 7303 [info@solidworks.com](info@solidworks.com) © 1995-2010, Dassault Systèmes SolidWorks Corporation, a Dassault Systèmes [S.A. company](S.A. company), 300 Baker Avenue, Concord, Mass. 01742 USA. All Rights Reserved. The information and the software discussed in this document are subject to change without notice and are not commitments by Dassault Systèmes SolidWorks Corporation (DS SolidWorks) . No material may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of DS SolidWorks. The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of this license. All warranties given by DS SolidWorks as to the software and documentation are set forth in the SolidWorks Corporation License and Subscription Service Agreement, and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such warranties. Patent Notices for SolidWorks Standard, Premium, Educational, and Professional Products U. S. Patents 5,815,154; 6,219,049; 6,219,055; 6,603,486; 6,611,725; 6,844,877; 6,898,560; 6,906,712; 7,079,990; 7,184,044; 7,477,262; 7,502,027; 7,558,705; 7,571,079; 7,590,497; 7,643,027; 7,672,822; 7,688,318; 7,694,238, and foreign patents,(e.g., EP 1,116,190 and JP 3,517,643) . U.S. and foreign patents pending. Trademarks and Other Notices for All SolidWorks Products SolidWorks, 3D PartStream.NET, 3D ContentCentral, PDMWorks, eDrawings, and the eDrawings logo are registered trademarks and FeatureManager is a jointly owned registered trademark of DS SolidWorks. SolidWorks Enterprise PDM, SolidWorks Simulation, SolidWorks Flow Simulation, and SolidWorks 2010 are product names of DS SolidWorks. CircuitWorks, Feature Palette, FloXpress, PhotoWorks, TolAnalyst, and XchangeWorks are trademarks of DS SolidWorks. FeatureWorks is a registered trademark of Geometric Ltd. Other brand or product names are trademarks or registered trademarks oftheir respective holders. COMMERCIAL COMPUTER SOFTWARE-PROPRIETARY U.S. Government Restricted Rights. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR 52.227-19 (Commercial Computer Software-Restricted Rights), DFARS 227.7202 (Commercial Computer Software and Commercial Computer Software Documentation), and in the license agreement, as applicable. Contractor/Manufacturer: Dassault Systèmes SolidWorks Corporation, 300 Baker Avenue, Concord, Massachusetts 01742 USA Copyright Notices for SolidWorks Standard, Premium, Educational, and Professional Products Portions ofthis software © 1990-2010 Siemens Product Lifecycle Management Software III (GB) Ltd. Portions ofthis software © 1998-2010 Geometric Ltd. Portions ofthis software © 1986-2010 mental images GmbH & Co. KG. Portions ofthis software © 1996-2010 Microsoft Corporation. All rights reserved. Portions ofthis software © 2000-2010 Tech Soft 3D. Portions ofthis software © 1998-2010 3Dconnexion. This software is based in part on the work of the Independent JPEG Group. All Rights Reserved. Portions ofthis software incorporate PhysX™ by NVIDIA 2006-2010 . Portions ofthis software are copyrighted by and are the property of UGS Corp. © 2010. Portions ofthis software © 2001-2010 Luxology, Inc. All Rights Reserved, Patents Pending. Portions ofthis software © 2007-2010 DriveWorks Ltd. Copyright 1984-2010 Adobe Systems Inc. and its licensors. All rights reserved. Protected by U.S. Patents 5,929,866; 5,943,063; 6,289,364; 6,563,502; 6,639,593; 6,754,382; Patents Pending. Adobe, the Adobe logo,

FAQs

What project and vehicle type does this document cover?

It covers the F1 in SchoolsTM Design Project using SolidWorks® software for Type-R cars.

What legal notices are included in the document?

It includes information-change disclaimers, restrictions on reproduction, license terms, patent notices, and trademark acknowledgements.

What does the table of contents start with?

The table of contents begins with Introduction, then covers how to use the book, SolidWorks basics, prerequisites, and conventions before outlining setup and design steps.

Oct 23, 2026

Upload by Jake