Environmental Product Declaration - XLam CLT Panel - Version 1st February 2021

Sep 15, 2026

Uploaded by Rizky

Environmental Product Declaration for XLam Cross-Laminated Timber (CLT) panels produced in Australia and used in Australia and New Zealand. The declaration is prepared under ISO 14025 and EN 15804+A1, referencing PCR 2012:01, and is valid until 1 February 2026. It quantifies impacts for a declared unit of 1 m3 of CLT at 13% average moisture content and density 480 kg/m3, covering treated/untreated and visual/non-visual grades, with data reference year 1 April 2019 to 31 March 2020.

LanguageEnglish

CategoryResearch & Report

FormatPDF

Pages22

Reading Time55 min

AccessFree to download

Introduction

Programme scope and product coverage

Manufacturer and production basis

Life cycle assessment study inputs

Product description and representative product

Panel dimensions and layer composition

Declared unit and classification

UN CPC and ANZSIC codes

Product composition and adhesive requirements

Pinus radiata and PEFC-certified sourcing

Independent verification and data follow-up

Third-party verification procedure

Environmental Product Declaration XLam CLT Panel Environmental Product Declaration (EPD) in accordance with ISO 14025 and EN 15804+A1 EPD Registration No. S-P-02326 Programme Operator: EPD Australasia Limited Version 1st February 2021 Valid until 1st February 2026 Scope: Australia Environmental Product Declaration-XLam CLT Panel Acknowledgements An Environmental Product Declaration, or EPD, is a standardised and verified way of quantifying the environmental impacts of a product based on a consistent set of rules known as a PCR (Product Category Rules) . The EPD owner has the sole ownership, liability, and responsibility for the EPD. Environmental Product Declarations within the same product category from different programmes may not be comparable. EPDs of construction products may not be comparable if they do not comply with EN 15804. Declaration Owner XLam Australia [Web:](Web: www.xlam.co.nz)[ www.xlam.co.nz](Web: www.xlam.co.nz) Email: Australia [enquiries@xlam.com.au](enquiries@xlam.com.au)[ ](enquiries@xlam.com.au)New Zealand [enquiries@xlam.co.nz](enquiries@xlam.co.nz) Post: 19 Bilston Drive, Barnawartha North VIC 3691 Australia Geographical scope: Australia Reference year for data: 1st April 2019 to 31st March 2020 EPD produced by [Web:](Web: www.thinkstep-anz.com)[ www.thinkstep-anz.com](Web: www.thinkstep-anz.com) Email: [anz@thinkstep-anz.com](anz@thinkstep-anz.com) Post: 25 Jubilee Street, South Perth WA 6151, Australia EPD Programme Operator EPD Australasia Ltd [Web:](Web: www.epd-australasia.com)[ www.epd-australasia.com](Web: www.epd-australasia.com) Email: [info@epd-australasia.com](info@epd-australasia.com) Post: EPD Australasia, 315a Hardy Street, Nelson 7010, New Zealand CEN standard EN 15804 (EN15804:2012+A1:2013) served as the core PCR PCR: PCR 2012:01 Construction products and Construction services, Version 2.33, 2020-09-18 PCR review was conducted by: The Technical Committee of the International EPD® System. Chair: Massimo Marino. Contact via [info@environdec.com](info@environdec.com). Independent verification of the declaration and data, according to ISO 14025: EPD verification (External) Third Party Verifier (approved by EPD Australasia) Andrew D Moore Life Cycle Logic Pty. Ltd. Web: [lifecyclelogic.com.au](lifecyclelogic.com.au) [Email:](Email: Andrew@lifecyclelogic.com.au)[ Andrew@lifecyclelogic.com.au](Email: Andrew@lifecyclelogic.com.au) Post: PO Box 571 Fremantle WA 6959 Australia Procedure for follow-up of data Procedure involves third Version History party verifier 􀂅 Yes 􀂅 No 1.0 2 Environmental Product Declaration-XLam CLT Panel Introduction This EPD has been prepared in accordance with ISO 14025:2006, EN 15804:2012+A1:2013, PCR 2012:01 and EPD Australasia (2015) . It covers XLam Cross-Laminated Timber (CLT) panels 85mm-315mm thick, treated or untreated, visual & non-visual grades manufactured at XLam’s manufacturing facility in Australia for use in buildings in Australia and New Zealand. Manufacturer Information This EPD covers cross-laminated timber panels produced at XLam Australia’s factory located in Wodonga, Victoria. This EPD is based on a life cycle assessment study compiled in October 2020 with input and environmental output data gathered for the period 1st April 2019 – March 31st 2020 conducted by thinkstep-anz. Product Description XLam CLT panels 85-315mm are structural timber panels made by face gluing together layers of finger-jointed Radiata Pine boards ranging from 20mm to 45mm thick with a moisture curing polyurethane adhesive in alternating 90 degree angles. Three, five or seven layers are pressed together in a hydraulic press while the glue cures. Panels 6-16 metres long and 2.4-3.4 metres wide can be manufactured. Products included in this EPD are: 3, 5 or 7 layers and 85-315mm thick. 3 Environmental Product Declaration-XLam CLT Panel Representative Product The rep

FAQs

What standard and PCR requirements govern this environmental product declaration?

The declaration is prepared in accordance with ISO 14025:2006 and EN 15804:2012+A1:2013, using PCR 2012:01 for construction products and construction services.

What does the declared unit represent in the EPD?

The declared unit is 1 m3 of XLam CLT at an average moisture content of 13% and a density of 480 kg/m3, covering treated or untreated and visual or non-visual grades.

Where and for what geographic scope are the XLam CLT panels manufactured and used?

The panels are produced at XLam Australia’s manufacturing facility in Wodonga, Victoria, for use in buildings in Australia and New Zealand, with geographic scope stated as Australia in the EPD.

Sep 15, 2026

Uploaded by Rizky

Environmental Product Declaration - XLam CLT Panel - Version 1st February 2021_Page 1

Open in WPS to view all 22 pages