Crathco Beverage Freezers - Operation and Instruction Manual - Models 5311, 5511, 5941, & 5711

Oct 17, 2026

Upload by Jasmine

Operation and Instruction Manual for Crathco® Beverage Freezers covering models 5311, 5511, 5941, and 5711. It provides warnings and operator safety precautions, then guides installation including shipment transit inspection, removal from carton and pallet, placement and required clearance, electrical connection requirements by model, and setup steps such as switch positioning and carb tube installation. It also includes optional concealed air filter accessory installation and outlines maintenance, troubleshooting, and service support sections for ongoing safe operation.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages72

Reading Time3 h 1 min

AccessFree to download

Warnings and Safety Precautions

Installation

Operating and Adjustments

Care and Cleaning

Maintenance Service

Troubleshooting

Exploded Views

Electrical Diagrams

Wiring Diagrams

Refrigeration Diagrams

Crathco® Beverage Freezers Operation and Instruction Manual for Models 5311, 5511, 5941, & 5711 | TABLE OF CONTENTS | | --- | | Warnings and Safety Precautions .....................3
Installation ...................................................4-6
Operating and Adjustments .......................6-11
Care and Cleaning ................................... 12-17
Maintenance Service ................................ 17-21
Troubleshooting .......................................22-23
Exploded Views ........................................24-40
Electrical Diagrams ...................................41-52
Wiring Diagrams ......................................53-67
Refrigeration Diagrams .............................68-69 | Prior authorization must be obtained from Model 5311 Grindmaster Corporation for all warranty claims. © Grindmaster Corporation, 2000 PRINTED IN USA Grindmaster Corporation 4003 Collins Lane Louisville, KY 40245 USA (502) 425-4776 (800) 695-4500 (USA & Canada only) FAX (502) 425-4664 [www.grindmaster.com](www.grindmaster.com) 0509 Form\# WH-330-09 Part\# W0600116 WARNING LABELS OPERATOR'S SAFETY PRECAUTIONS 1) Read and understand the operating instructions in this manual thoroughly. 2) Note all warning labels on the freezer. If any of the warning labels are missing or damaged replace them immediately. 3) Do not wear loose fitting garments or jewelry which could cause a serious accident. 4) Stay alert at all times during operation. 5) Keep operating area clean. 6) Do not operate freezer if any excessive noise or vibration occurs. Contact your authorized service agent. Located on the right, left and rear panels. INSTALLATION Shipment Transit 1) 2) The freezer has been operated and tested at the factory. Upon arrival the complete freezer must be thoroughly checked for any damage which may have occurred in transit. Note: A tip (N) Tell warning device is placed on each shipping carton at the factory. If the arrow tip is blue, the carton has been tipped in transit. (See Figure A) THE CARRIER IS RESPONSIBLE FOR ALL DAMAGE IN TRANSIT WHETHER VISIBLE OR CONCEALED. DO NOT PAY THE FREIGHT BILL until the freezer has been checked for damage. Have the carrier note any visible damage on the freight bill. If concealed damage and/or shortages are found later, advise the carrier within 10 days and request inspection. The customer must place any claim for damage and/or shortage with the carrier. Grindmaster Corporation cannot make any claims against the carrier. Crathco® 5000 Series Manual Page 3 Removal from Carton and Pallet 1) 2) 3) 4) 5) 6) 􀀂 Remove staples or cut cardboard box around the stapled area. Pull the cardboard box up off machine. Remove the Styrofoam packing and the plastic bag. Remove both side panels with screwdriver. Use a wratchet with a 3 inch extension and a 7/16 socket to remove the shipping bolts (connecting the machine to the pallet) located on both sides of the frame bottom plate. Supporting all four sides, lift machine up and place in appropriate area. CAUTION: If equipped with spinner do not lift unit by spinner shaft to avoid serious damage to spinner. Installing Your Unit 􀀂 1) 􀀂 2) 3) 4) 5) 6) CAUTION: Do not alter or deform the plug in any way! Altering or deforming plug may damage unit and will void warranty! Receptacle required: NEMA 5-15R for model 5941, NEMA 5-20R for model 5311, and NEMA 6-20R for models 5511 and 5711. Place freezer in a location that allows adequate space at each side and above for proper air circulation. Minimum clearance is: 6”(15 cm) on both sides 0” at back and open above the freezer. (See Figure B) CAUTION: Failure to allow adequate ventilation will void the warranty and reduce freezer performance. Place the freezer on the self-sealing rubber pad on a level counter that is stable and strong enough to safely support its weight (20

FAQs

What should be checked upon freezer arrival for shipment damage?

Thoroughly check the complete freezer for any damage that may have occurred in transit. If there is concealed damage or shortages, advise the carrier within 10 days and request inspection.

What electrical receptacle types are required for different freezer models?

Use NEMA 5-15R for model 5941, NEMA 5-20R for model 5311, and NEMA 6-20R for models 5511 and 5711.

What clearance is required for proper air circulation during installation?

Minimum clearance is 6 inches (15 cm) on both sides, 0 inches at the back, and open above the freezer.

Oct 17, 2026

Upload by Jasmine