COILS INSTALLATION INSTRUCTIONS - Important Safety Instructions - Shipping Inspection - Codes & Regulations - Replacement Parts - Pre-Installation Instructions

Oct 23, 2026

Uploaded by Bintang

Comprehensive coil installation instructions covering critical safety guidance, shipment arrival inspection, and safe handling requirements for transporting and positioning equipment without damaging piping. Details compliance expectations with applicable national codes and wiring regulations, including refrigerant handling considerations tied to environmental requirements. Provides multiple safety warnings for fire risk, ventilation during hot work, authorized service personnel, and high-voltage precautions. Includes requirements for verifying components, using model/serial numbers for service parts, and minimum clearance routing before installation.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages16

Reading Time40 min

AccessFree to download

Important Safety Instructions

Shipping Inspection

Handling

Codes & Regulations

Replacement Parts

Pre-Installation Instructions

UPFLOW/DOWNFLOW COILS INSTALLATION INSTRUCTIONS 1. Important Safety Instructions The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It is the owner’sand installer’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of personal injury, property damage, and/or product damage. NOTE: This unit should be installed in a manner so that it is not accessible to the general public. 2. Shipping Inspection This equipment is approved for use with R32 refrigerant only. Upon receiving the product, inspect it for damage from shipment. Shipping damage, and subsequent investigation is the responsibility of the carrier. Verify the model number, specifications, and accessories are correct prior to installation. The distributor or manufacturer will not accept claims from dealers for transportation damage or installation of incorrectly shipped units. 2.1 Handling Use caution when transporting/carrying unit. Do not carry unit with hooks or sharp object. The preferred method of carrying the unit after arrival at the job site is to carry by two-wheel hand truck from the back or sides or by hand by carrying at the cabinet corners. Take proper precautions when carrying unit to avoid any damage to the piping. 3. Codes & Regulations This product is designed and manufactured to comply with national codes such as ASHRAE 15, ASHRAE 15.2, IAPMO Uniform Mechanical Code, ICC, International Mechanical Code, or CSAB52 . The product shall be installed in accordance with national wiring regulations. Installation in accordance with such codes and/or prevailing local codes/regulations is the responsibility of the installer. Compliance with national gas regulations shall be observed. The manufacturer assumes no responsibility for equipment installed in violation of any codes or regulations. The United States Environmental Protection Agency (EPA) has issued various regulations regarding the introduction and disposal of refrigerants. Failure to follow these regulations may harm the environment and can lead to the imposition of | WARNING | | --- | | If any hot work is to be conducted on the refrigerating equipment or an associated parts, appropriate fire extinguishing equipment shall be available on hand. Have a dry powder or CO2 fire extinguisher adjacent to the hot work area.
Ensure that the area is in the open or that it is adequately ventilated before breaking into the system or conducting any hot work. A degree of ventilation shall continue during the period that the work is carried out. The ventilation should safely disperse any released refrigerant and preferably expel it externally into the atmosphere. | WARNING Only personnel that have been trained to install, adjust, service, maintenance or repair (hereinafter,“service”) the equipment specified in this manual should service the equipment. This equipment is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the equipment. The manufacturer will not be responsible for any injury or property damage arising from improper supervision, service or service procedures. If you service this unit, you assume responsibility for any injury or property damage which may result. In addition, in jurisdictions that require one or more licenses to service the equipment specified in this manual, only licensed personnel should service the equipment. Improper supervision, installation, adjustment, servicing, maintenance or repair of the equipment specified in this manual, or attempting to install, adjust, service or repair the equipment spec

FAQs

What must be checked upon receiving the product?

Upon receiving the product, inspect it for shipment damage, verify the model number, specifications, and accessories are correct, and confirm all required components are present and intact. Missing components should be reported immediately to the manufacturer or distributor.

Oct 23, 2026

Uploaded by Bintang