Centaur PP - Safety Data Sheet - First-aid, Firefighting, Handling, Storage

Oct 6, 2026

Centaur PP safety data sheet provides structured guidance for safe handling of a polypropylene-based polymer blend used for FFF/FDM 3D printing in monofilament or granule form. It states no classification as dangerous under EC Regulation 1272/2008, while warning of burn hazards from heated or molten material. Sections cover composition and additives, first-aid actions for inhalation/skin/eyes/ingestion, firefighting media and protective equipment, accidental release control, and storage and handling precautions, plus exposure controls and hygiene measures.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages4

Reading Time10 min

AccessFree to download

1. Identification of the substance/preparation and of the company

1.1 Trade name

1.4 Identification of the company

2. Hazards identification

2.1 Risk advice to man and the environment

2.2 Classification of the substance or mixture

3. Composition / information on ingredients

3.2 CAS number

3.3 Additional information

4. First-aid measures

4.1 If inhaled

4.5 Note to the physician

5. Firefighting measures

5.1 Suitable extinguishing media

5.3 Special protective equipment

6. Accidental Release Measures

6.1 Personal precautions

6.3 Methods for cleaning up

7. Handling and storage

7.1 Handling

7.3 Precautions

8. Exposure controls / personal protection

8.2 Exposure controls

8.3 Personal protective equipment

9. Physical and chemical properties

9.1 Form

9.8 Density

10. Stability and reactivity

10.2 Conditions to avoid

10.4 Hazardous reactions

11. Toxicological information

11.1 Information on toxicological effects

Centaur PP 1. Identification of the substance/preparation and of the company 1.1 Trade name: 1.2 Chemical name: 1.3 Typical use of the material: 1.4 Identification of the company: Centaur PP Polypropylene based polymer blend Monofilament or granules for FFF/FDM technology based 3D printing Formfutura BVGroenestraat 215 6531 HH Nijmegen The Netherlands Phone: +31 (0)85 002 0881 Emergency phone number: +31 (0)30 274 8888 2. Hazards identification 2.1 Risk advise to man and the environment: No risk exists to the health of users if the product is handled and processed properly. 2.2 Classification of the substance or mixture: Not classified as dangerous according to Regulation (EC) No 1272/2008 . 2.3 Special advice on hazards: Danger of burns while handling the heated or molten product. 3. Composition / information on ingredients 3.1 Chemical nature: 3.2 CAS number: 3.3 Additional information: Polypropylene based polymer enhanced for 3D printing. - No harmful substances used. The product may contain varying levels of additives such as slip-and anti-blocking agents, antioxidants and stabilisers. 4. First-aid measures 4.1 If inhaled: After inhalation of decomposition products, gases or dust, bring the affected person to a 4.2 On skin contact: 4.3 On contact with eyes: 4.4 On ingestion: 4.5 Note to the physician: source of fresh air and keep calm. Contact a physician in case of discomfort. In case of contact with melted material, immediately cool the skin with plenty of cold running water. Removal of adhering to skin polymer, or burns caused by molten material require hospital treatment. In case of contact with eyes, rinse open eyes thoroughly with water. If symptoms occur, seek immediate medical attention. No effects known. Rinse mouth with water and then drink plenty of water. Seek medical attention if difficulties or discomfort occur. Treat symptomatically 5. Firefighting measures 5.1 Suitable extinguishing media: Dry chemical powder, foam, water, CO2. 5.1.1 Unsuitable extinguishing media: Do not use a solid water stream as it may scatter and spread fire. 5.2 Specific hazards: Carbon monoxide (CO), carbon dioxide (CO2), hydrocarbons and other gaseous products during incomplete combustion. The substances mentioned can be releases at highly elevated temperatures and in case of fire. 5.3 Special protective equipment: Full protective clothing and self-contained breathing apparatus. 5.4 Further information: Dispose of fire debris and contaminated extinguishing water in accordance with official regulations. 6. Accidental Release Measures 6.1 Personal precautions: 6.2 Environmental precautions: 6.3 Methods for cleaning up: Use personal protective equipment/clothing (see Section 8) . Avoid eye contact and dust formation and remove all sources of ignition. Sweep up to prevent slipping hazard. Prevent entry into drainage systems, or surface water. Sweep/shovel into suitable container for disposal. Avoid raising dust and ensure adequate ventilation. 7. Handling and storage 7.1 Handling: 7.2 Storage: 7.3 Precautions: 7.4 Specific end use(s): Handle in a well ventilated area. Install local exhaust at 3D printers area is recommended when many printers are operated at once. Avoid contact with heated or molten product. Use personal protective equipment (see Section 8) . Avoid dust formation and electrostatic charge. Keep away from fire ignition sources. Protect from water and moisture. Store material in dry rooms and keep material in closed packaging/container with desiccant when not in use. Store at ambient temperatures. Avoid all sources of ignition. No special precautions required. Primarily used for 3D printing. 8. Exposure controls / personal protection 8.1 Occupational exposure limits: Given suitable ventilation it can be that the threshold limits will not be 8.2 Exposure controls: 8.3 Personal protective equipment 8.

FAQs

What is Centaur PP typically used for?

Centaur PP is a polypropylene-based polymer blend used as monofilament or granules for FFF/FDM technology-based 3D printing.

Is Centaur PP classified as dangerous under EC Regulation 1272/2008?

No. The mixture/substance is stated as not classified as dangerous according to Regulation (EC) No 1272/2008.

What hazards should users watch for during handling?

The sheet highlights danger of burns while handling heated or molten product. It also advises avoiding dust formation and electrostatic charge during use.

Oct 6, 2026

Uploaded by CatatanPagi