CEMENT ALL - Multi-Purpose Repair Material & Non-Shrink Grout - Product Datasheet

Nov 2, 2026

Uploaded by dbqoiu

Rapid Set® CEMENT ALL® is a high-performance, fast-setting concrete repair material and non-shrink grout for durable performance in wet environments. It blends Rapid Set hydraulic cement with specially graded fine aggregates, remains non-metallic with no added chlorides, and produces a workable mix when combined with potable water. It sets in 15 minutes and reaches structural strength in 1 hour, supporting general and structural repairs, grouting, doweling, anchoring, and trowel or casting applications.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages2

Reading Time5 min

AccessFree to download

Description

Uses

Environmental Advantages

Application

Surface Preparation

Mixing

Placement

Highlights

Curing

Cold Weather

Warm Weather

CEMENT ALL Multi-Purpose Repair Material & Non-Shrink Grout PRODUCT DATASHEET DESCRIPTION: Rapid Set® CEMENT ALL® is a high-performance, fast-setting, multipurpose concrete repair material and non-shrink grout. Durable in wet environments, CEMENT ALL is a blend of Rapid Set hydraulic cement and specially graded fine aggregates. CEMENT ALL is non-metallic and no chlorides are added. Mix CEMENT ALL with water to produce a workable, high quality material that is ideal where rapid strength gain and high durability are desired. CEMENT ALL sets in 15 minutes and achieves structural strength in 1 hour.* USES: Use CEMENT ALL for general and structural concrete repair, doweling and anchoring, industrial grouting, formed work, vertical and horizontal trowel applications. CEMENT ALL is ideal for airport, highway, industrial and marine applications. ENVIRONMENTAL ADVANTAGES: Use CEMENT ALL to reduce your carbon footprint and lower your environmental impact. Production of Rapid Set cement emits far less CO2 than portland cement. Contact your CTS representative for EPD, LEED values and other sustainability information. APPLICATION: Apply CEMENT ALL in thicknesses from featheredge to 4" (10 cm) . For heavy loads and vehicle traffic, minimum thickness will vary. For deeper sections, use Rapid Set® Mortar Mix or Rapid Set® Concrete Mix. Not intended for extended exposure over 212°F (100°C) . For overlay applications, a minimum of one test section should be prepared to evaluate the suitability of the materials and procedures. SURFACE PREPARATION: For repairs, application surface must be clean, sound and free from any materials that may inhibit bond, such as oil, asphalt, curing compound, acid, dirt and loose debris. Roughen surface and remove all unsound material. Apply CEMENT ALL to a surface that is thoroughly saturated with no standing water. MIXING: The use of a power-driven mechanical mixer, such as a mortar mixer or a drillmounted mixer, is recommended. Organize work so that all personnel and equipment are in place before mixing. Use clean potable water. CEMENT ALL may be mixed using 3 to 3.75 quarts (2.8 L to 3.5 L) of water per 55-lb (25 kg) bag for Department of Transportation projects and other critical applications. For general purpose and high fluidity applications, a maximum of 5 quarts (4.7 L) may be used. Use less water to achieve higher strengths. For increased fluidity and workability, use Rapid Set® FLOW Control plasticizing admixture. Place the desired quantity of mix water into the mixing container. While the mixer is running, add CEMENT ALL. Mix for the minimum amount of time required to achieve a lump-free, uniform consistency (usually 1 to 3 minutes) . Do not retemper. PLACEMENT: CEMENT ALL may be placed using traditional construction methods. Organize work so that all personnel and equipment are ready before placement. Place, consolidate and screed quickly to allow for maximum finishing time. Use a method of consolidation that eliminates air voids. Do not wait for bleed water; apply final finish as soon as possible. CEMENT ALL may be troweled, floated or broom finished. On flat work, do not install in layers. Install full-depth sections and progress horizontally. Do not install on frozen surfaces. To extend working time, use Rapid Set® SET Control retarding admixture or use cold mix water. CEMENT ALL may be applied in temperatures ranging from 45°F to 90°F (7°C to 32°C) . Under dry ambient conditions, water based coatings such as latex paint can be applied after 4 hours. Solvent based and impermeable coatings such as oil based paint and epoxy can be applied after 16 hours. OVERVIEW Highlights: Fast: Sets in 15 minutes, structural strength in 1 hour* | Durable: Formulated for long life in critical applications | | --- | | Excellent Bond: Superior adhesion to concrete, stone, brick, block, stucco and more | | Structural: For repair and new construction | | Multi-Purpose: Use for concrete repair,

FAQs

What is CEMENT ALL, and what performance makes it suitable for repairs and grouting?

CEMENT ALL is a fast-setting concrete repair material and non-shrink grout formulated for high performance. It sets in 15 minutes and achieves structural strength in 1 hour, helping deliver rapid strength gain and high durability.

What are the recommended mix and water ratios for CEMENT ALL?

Use clean potable water. For Department of Transportation projects and critical applications, mix with 3 to 3.75 quarts (2.8 L to 3.5 L) of water per 55-lb (25 kg) bag. For general purpose and high fluidity, a maximum of 5 quarts (4.7 L) may be used, and less water is used to achieve higher strengths.

How should CEMENT ALL surfaces be prepared and cured?

Repair surfaces must be clean, sound, and free of materials that can inhibit bond, then roughen and remove unsound material. Apply to a thoroughly saturated surface with no standing water, and water-cure by keeping exposed surfaces wet for at least 1 hour, beginning after hardening starts and before the surface loses its moist sheen.

Nov 2, 2026

Uploaded by dbqoiu