BMW 2500,2800,3.0,3.3 Bavaria 1968-77 - Workshop Manual

Nov 4, 2026

Uploaded by Marglet

Autobook Workshop Manual content covering BMW 2500, 2800, 3.0 and 3.3 models in the Bavaria series for years 1968-77. Provides an introduction for do-it-yourself owners, outlining step-by-step servicing and repair guidance, the use of special tools only when necessary, and a fault diagnosis approach at the end of each chapter. Includes Chapter 1, Engine, with a description of the in-line six-cylinder single overhead camshaft setup and detailed subsections on oil pump, sump removal, fuel pump operation, and lubrication system components.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages169

Reading Time7 h 6 min

AccessFree to download

ACKNOWLEDGEMENT

INTRODUCTION

CHAPTER 1 THE ENGINE

1:1 Description

1:2 Removing and refitting the engine

1:3 Removing and refitting cylinder head

1:4 Servicing head, valves and camshaft

1:5 Valve clearance adjustment

1:6 Timing gear

1:7 External oil filter

1:8 Sump removal and refitting

1:9 Oil pump and strainer

1:10 Pistons and connecting rods

1:11 Flywheel and pilot bearing

1:12 Crankshaft oil seals

1:13 Crankshaft removal and refitting

1:14 Fault diagnosis

BMW 2500,2800,3.0,3.3,Bavaria 1968-77Autobook By Kenneth Ball and Mary Ball and the Autobooks Team of Technical Writers BMW 25001968-77 BMW 28001968-71 BMW 2800 CS,CA 1968-71 BMW 3.0 S,SA,SI 1971-77 BMW 3.0 CS,CSA,CSI,CSL 1971-75 BMW 3.0 LA 1975-77 BMW 3.3 L,LA,LIA 1974-77 BMW Bavaria 1972-74 Mary Ball with her 2800 CS at 49,000 miles The AUTOBOOK series of Workshop Manualsis the largest in the world and covers themajority of British and Continental motor cars,as well as the majority of Japanese andAustralian models. Whilst every care has been taken to ensurecorrectness of information it is obviously notpossible to guarantee complete freedom fromerrors or omissions or to accept liability arisingfrom such errors or omissions. CONTENTS Acknowledgement Introduction Chapter 1 The Engine9Chapter 2 The Fuel System33Chapter 3The Ignition System47Chapter 4The Cooling System55Chapter 5The Clutch61Chapter 6Manual Transmission69Chapter 7Automatic Transmission75Chapter 8Propeller Shaft,Rear Axle andRear Suspension83Chapter 9Front Suspension and Hubs95Chapter 10The Steering Gear103Chapter 11The Braking System113Chapter 12The Electrical System127Chapter 13 The Bodywork135Appendix141 ISBN 0851476619 First Edition 1977 ◎Autobooks Ltd 1977 All rights reserved.No part of this publication may bereproduced,stored in a retrieval system,or transmitted inany form or by any means,electronicmechanical,photocopying,recording or otherwse,without the priorpermission of Autobooks Ltd. Printed in Brighton Engand for Autobooks Ltd by G.Beard and Son LtdBound in Hove England for Autobooks Ltd by Jilks Ltd A # ACKNOWLEDGEMENT Our thanks are due to BMW for their unstinted co-operation and also forsupplying data and illustrations. Considerable assistance has also been given by owners,who have discussedtheir cars in detail,and we would like to express our gratitude for this invaluableadvice and help. Kenneth Ball and Mary BallDitchling Sussex England. # INTRODUCTION This do-it-yourself Workshop Manual has been specially written for the ownerwho wishes to maintain his vehicle in first class condition and to carry out thebulk of his own servicing and repairs.Considerable savings on garage chargescan be made,and one can drive in safety and confidence knowing the work hasbeen done properly. Comprehensive step-by-step instructions and illustrations are given on mostdismantling,overhauling and assembling operations.Certain assemblies requirethe use of expensive special tools,the purchase of which would be unjustified.In these cases information is included but the reader is recommended to handthe unit to the agent for attention. Throughout the Manual hints and tips are included which will be foundinvaluable,and there is an easy to follow fault diagnosis at the end of eachchapter. Whilst every care has been taken to ensure correctness of information it isobviously not possible to guarantee complete freedom from errors or omissionsor to accept liability arising from such errors or omissions. Instructions may refer to the righthand or lefthand sides of the vehicle or thecomponents.These are the same as the righthand or lefthand of an observerstanding behind the vehicle and looking forward. # CHAPTER 1THE ENGINE 1:8 Sump removal and refitting # 1:1 Description 1:9 Oil pump and strainer 1:2 Removing and refitting the engine 1:3 Removing and refitting cylinder head 1:4 Servicing head,valves and camshaft 1:5 Valve clearance adjustment 1:6 Timing gear 1:7 External oil filter 1:1 Description The engine is an in-line,six-cylinder,single overheadcamshaft unit with crossflow induction and exhaust.Asection through a cylinder and valve gear is shown inFIG 1:1,a section through the engine timing gear inFIG 1:2.The camshaft is driven by roller chain from asprocket on the crankshaft.The valves,set in line alongeach side of the light alloy cylinder head,operate inpressed-in valve guides.Cast iron valve

FAQs

What is the purpose of this Autobook manual for BMW owners?

It is written for owners who want to maintain the vehicle and handle most servicing and repairs themselves, aiming to reduce garage charges and support safe, confident driving.

Does the manual provide step-by-step instructions and illustrations?

Yes. Comprehensive step-by-step instructions and illustrations are included for most dismantling, overhauling, and assembling operations.

What does Chapter 1 cover about the BMW engine?

Chapter 1 details engine construction and systems, including an in-line six-cylinder single overhead camshaft description and lubrication components, plus procedures and fault diagnosis sections for major engine assemblies.

Nov 4, 2026

Uploaded by Marglet