BENNETT 719 ELECTRONICS - Technical and Dispenser Programming Manual - Rev E - 4/2/18

Nov 4, 2026

Uploaded by hdkawk

Technical and dispenser programming manual for Bennett 719 electronic 3000 Series remote and self-contained dispensers, covering retail/commercial DEF model units. Provides safety requirements, installation and operation guidance, and instructions to power up correctly while preventing injury, death, or equipment damage. Includes shipment inspection and carrier liability notes, FCC compliance conditions, and revision history. Also organizes content through a detailed table of contents covering safety, introduction, specifications, theory of operation, and dispenser programming.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages106

Reading Time4 h 27 min

AccessFree to download

Safety Instructions

Introduction

General Information

Introduction to the 719 Electronics

719 Section Categories

Specifications

Abbreviations and Acronyms

Board Dimensions

Block Diagram

Overview

Theory of Operation

Component Description

Connector Settings

Programming

Programming the Dispenser

Default Settings

BENNETT 719 ELECTRONICS 3000 Series Electronic Remote & Self-Contained Dispensers Retail and Commercial or DEF Model Units Technical and Dispenser Programming Manual 135091 Rev E 4/2/18 Only Trained Personnel May Work on This Equipment READ THIS MANUAL This manual has important information for safe installation and operation of this equipment. Read and understand this manual before applying power. Keep this manual and tell all service personnel to read this manual. If you do not follow the instructions, you can cause bodily injury, death, or damage to the equipment. The material included in this installation manual is accurate at the date of publication. The intent of this manual is to assist. If further assistance is required, please contact the Bennett Technical Service Department at 1-800-423- 6638. Bennett Marketing Services can be contacted by mail, facsimile, telephone or e-mail at the locations specified below: Bennett Pump Company Marketing Services 1218 East Pontaluna Road Spring Lake, MI 49456 Telephone from USA 1-800-235-7618 Telephone from outside USA 231-798-1310, Extension 287 or 269 Customer Service USA 231-719-6050; Facsimile USA 231-799-6202 Email: sales@bennettpump.com or [salesintl@bennettpump.com](salesintl@bennettpump.com) [Website:](Website: www.bennettpump.com)[ ](Website: www.bennettpump.com)[www.bennettpump.com](Website: www.bennettpump.com) For new manuals, visit our web page [at](at www.bennettpump.com)[ ](at www.bennettpump.com)[www.bennettpump.com](at www.bennettpump.com) IMPORTANT Examine the shipment immediately upon arrival to make certain there has been no damage or loss in transit. Bennett Pump Company, as shipper, is not liable for the hazards of transportation. Please make damage claims directly to the truck line. NOTICE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interface, and (2) this device must accept interference received, including interference that may cause undesired operation. | Revision Level | Date | Description | | --- | --- | --- | | A | 7/19/17 | Original Document | | B | 10/11/17 | Changed Mode 19 How to Program Pulse Output to be Mode 50 Page 33-Added PPV 5-Digit Display prices to Menu Code 8 Figure 8.1. Page 48-Added Mode 24 – How to Set the Solenoid Valve Type
Page 49-Added Mode 26 – How to Reset Shift Totals
Page 58-Added Mode 31 – How to Program Total Access
Page 70-Added Mode 96 – Proportional Valve
Page 82 – Added 8-digit display error text to error codes. | | C | 11/8/17 | Page 39 – Changed the flash option default to 0
Page 41 – Renamed Battery Timer to Mode 16
Page 69-Added Mode 86 – How to Program High Flow/Low Flow Selector Switch Page 82 – Added error codes 18, 28, 38, 48, and 58 | | D | 12/4/17 | Page 8 – Add P1, P2, P3,and P4 locations
Page 14 – Add P1, P2, P3,and P4 connector descriptions
Page 87 – Added FuelForce to POS/Fuel Controller Table
Page 90 – Added Commercial Communication information | | E | 4/2/18 | Page 17 – Added Menu Codes 49, 80, and 81 to table.
Page 64 – Added Mode 49 – How to reboot the software
Page 70 – Added Mode 80 – Valve Diagnostics
Page 71 – Added Mode 81 – How to Cycle the Motors
Page 82 – Added error codes 18, 28, 38, 48, and 58
Removed Mode 86 – How to Program High Flow/Low Flow Selector Switch | TABLE OF CONTENTS SAFETY INSTRUCTIONS III INTRODUCTION 1 General Information....................................................................................................................................................................................................... 1 Introduction to the 719 Electronics ......................................................................................................................................................................... 1 719 Section Categories...........................................

FAQs

Who is allowed to work on the Bennett 719 electronics equipment?

Only trained personnel may work on this equipment.

What should be done before applying power?

Read and understand the manual before applying power, and follow its installation and operation instructions.

What should be checked immediately upon arrival of the shipment?

Examine the shipment immediately to ensure there has been no damage or loss in transit, and make damage claims directly to the truck line.

Nov 4, 2026

Uploaded by hdkawk