Audi 6-Speed Manual Gearbox 01E 4-Wheel Drive Workshop Manual - Edition 03.92

Oct 29, 2026

Workshop manual for the Audi V8 6-speed manual gearbox 01E 4WD, edition 03.92, providing service and technical information for foremen and mechanics. It lists repair groups and technical bulletin usage, then presents contents covering gearbox identification, code letters, allocation, ratios, capacities, final drive identification, power flow diagrams, and transmission ratio calculations. It further outlines general repair instructions and detailed procedures for clutch, selector mechanism, gearbox removal/installation, and final drive/differential components, including seals, sensors, and propshaft servicing.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages68

Reading Time2 h 51 min

AccessFree to download

Workshop Manual Overview

Repair Groups and Technical Bulletins

Contents Overview

Gearbox Identification

Installation Application

Code Letters, Allocation, Ratios, Capacities

Final Drive Identification

Allocation to Gearbox 01E 4WD

# Workshop ManualAudi V81989▶ 6-Speed Manual Gearbox 01 E # Booklet 4-Wheel Drive Edition 03.92 Service Department.Technical Information Service. List of Workshop Manual Repair Groups Audi V81989▶ | 6-Speed Manual Gearbox 01 E4-Wheel Drive
Booklet
Edition 03.92 | | --- | When filing a Technical Bulletin enter the Bulletin No.in the adjacent column.When using the WorkshopManual you can then see at a glance whether Technical Bulletins have been published in respect of theparticular Repair Group in which you are looking. | Repair Group | Technical Bulletins | | | | | | | --- | --- | --- | --- | --- | --- | --- | | 00 Technical data | | | | | | | | 30 Clutch | | | | | | | | 34 Controls,Housing* | | | | | | | | 35
Gears,Shafts* | | | | | | | | 39 Front final drive,Differential* | | | | | | | | 39 Rear final drive,Differential* | | | | | | | | | | | | | | | | | | | | | | | | *Not or not fully described in this booklet | | | | | | | | →Note on opposite page | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Technical information should always be available to all foremen and mechanics,because their com-pliance with the instructions given is essential to ensure vehicle roadworthiness and safety. In addition,the normal safety precautions to be observed when working on motor vehicles are alsoapplicable. | Contents | | | --- | --- | | 00 Technical data | Page | | Gearbox identification | 00-1 | | -Code letters,allocation,ratios,capacities | 00-3 | | Final drive identification | 00-5 | | -Code letters,allocation,ratios,capacities | 00-7 | | Power flow diagram | 00-8 | | Calculation of transmission rati | 00-9 | | Notes regarding output test,brake test and towing vehicle | 00-10 | | General repair instructions | 00-11 | | | | | 30 Clutch | Page | | Servicing clutch mechanism | 30-1 | | -List of operations for pedal cluster (3.6 litre engine) | 30-1 | | -Removing and installing over-centre spring | 30-8 | | -List of operations for pedal cluster(4.2 litre engine) | 30-9 | | -Removing and installing over-centre spring | 30-16 | | -List of operations for hydraulics | *) | | -Bleeding clutch system | *) | | Servicing clutch release mechanism | “) | | Servicing clutch | 30-17 | | | | | 34 Controls,Housing | Page | | Servicing selector mechanism | *) | | Adjusting and checking selector mechanism | *) | | Removing and installing gearbox | 34-1 | | -Removal | 34-1 | | -Installation | 34-13 | | Removing and installing oil pump | 34-17 | | -Removal | 34-17 | | -Installation | 34-20 | | | | | 39 Final drive,Differential | Page | | Replacing flanged shaft seal | 39-1 | | Replacing electronic speedometer sender and gear | 39-2 | | Replacing flange/propshaft seal at gearbox | 39-4 | | -Sequence of operations | 39-6 | | Removing and installing propshaft | 39-10 | | -Sequence of operations | 39-13 | | -Adjusting | 39-18 | | Replacing flange/propshaft seal at rear final drive | 39-22 | | -Sequence of operations | 39-24 | | Replacing oil seal for right flanged shaft | 39-37 | | Replacing oil seal for left flanged shaft | 39-41 | | Removing and installing rear final drive | 39-47 | | -Removal | 39-47 | | -Installation | 39-58 | | | | | ”)Not described in this booklet | | | →Workshop Manual Audi 1001991 | | | Booklet 5-and 6-Speed Manual Gearbox 01E Edition 01.92 | | | | | ## Gearbox identification The 6-speed manual gearbox01E 4WD is installedin the Audi V8 from 07.91 in combination with the 3.6 litre a

FAQs

Which vehicles and engines use the 6-speed manual gearbox 01E 4WD?

The 6-speed manual gearbox 01E 4WD is installed in the Audi V8 from 07.91, combined with 3.6 litre and 4.2 litre 8-cylinder fuel injection engines.

Where are the gearbox code letters listed?

The code letters of the gearbox are also listed on the vehicle data plates.

What information does the manual provide under gearbox identification?

It provides gearbox identification details including code letters, serial numbers, allocation, gear ratios, and capacities, along with related specifications.

Oct 29, 2026

Upload by River Wang