AS-3017 - Arnott Front Air Strut Installation Instructions - Dodge Ram 1500 (DS/DJ) - Rev 1

Oct 22, 2026

Uploaded by Jacob

Installation instructions for the Arnott AS-3017 front air suspension product for Dodge Ram 1500 (DS/DJ). The manual stresses correct installation for benefits, using fully qualified ASE-certified professionals, and following required safety measures, including lifting, immobilizing, relieving air-system pressure, and protecting against stored energy. It provides general handling guidance, cautions on sequence and electric short-circuit prevention, and step-by-step removal and installation of the air strut, air fittings, lines, and torque to manufacturer specifications, ending with inflation reference and completion checks.

LanguageEnglish

CategoryHealthcare

FormatPDF

Pages9

Reading Time23 min

AccessFree to download

General Information

Air Shock Removal

Air Shock Installation

| AS-3017
ARNOTT FRONT AIR STRUT DODGE RAM 1500 (DS/DJ) | | | --- | --- | | Congratulations on your purchase of an Arnott® air suspension product. We at Arnott Incorporated are proud to offer a high quality product at the industry’s most competitive pricing. Thank you for your confidence in us
and our product.
Proper installation is essential to experience and appreciate the benefits of this system. Please take a moment to review these installation instructions before you begin to install these components on your vehicle. The removal and installation of air suspension products should only be performed by a fully qualified, ASE
Certified, professional.
It is equally important to be aware of all necessary safety measures while installing your new Air Suspension System. This includes proper lifting and immobilizing of the vehicle and isolation of any stored energy to
prevent personal injury or property damage.
"Engineered to Ride, Built to Last®"
WARNING: The air suspension system is under pressure (up to 10 bar, or 150 lbf/in). Verify pressure has been relieved and disconnect power to the air suspension system prior to disassembly. Do not allow dirt or grease to enter the system. Always wear standard hand, ear, and eye protection when servicing the air suspension system.
Arnott® is committed to the quality of its products. If you have a question or problem with any Arnott product, please contact Arnott by calling 800-251-8993 during normal business hours or email [techassistance@arnottinc.com](techassistance@arnottinc.com).
(In the EU please call +31 (0)73 7850 580 or email [info@arnotteurope.com](info@arnotteurope.com)) | | | 1 | A-3017 REV 1 07/16/2018 | | AS-3017
ARNOTT FRONT AIR STRUT DODGE RAM 1500 (DS/DJ) | | | --- | --- | | GENERAL INFORMATION:
Reading this manual signifies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement, the full [text of which is available at ](text of which is available at www. arnottinc.com)[ www. arnottinc.com](text of which is available at www. arnottinc.com).
• Not to be stored below 5oF (-15oC) or above 122oF (50oC).
• Avoid damage to air lines and cables.
• Removal and installation is only to be performed by fully qualified personnel.
• Use car manufacturer’s diagnostic software.
CAUTION: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
AIR SHOCK REMOVAL
1. SET STEERING TO STRAIGHT AHEAD.
2. RAISE VEHICLE.

NOTE: REFER TO THE SERVICE MANUAL FOR PROPER DEFLATION PROCEDURE.
3. REMOVE APPLICABLE FRONT WHEEL. (FIGURE 1)

FIGURE 1 | | | 2 | A-3017 REV 1 07/16/2018 | | AS-3017
ARNOTT FRONT AIR STRUT DODGE RAM 1500 (DS/DJ) | | | | --- | --- | --- | | 4. LOOSEN AND REMOVE THE TIE ROD END NUT. (FIGURE 2)

FIGURE 2
5. LOOSE AND REMOVE THE TWO SWAY BAR END LINK NUTS. (FUGURES 3, 4) | | | | | | | | FIGURE 3 FIGURE 4
6. LOOSEN AND REMOVE THE UPPER CONTROL ARM NUT. (FIGURE 5)
| | | | 3 | A-3017 REV 1 07/16/2018 | | | AS-3017
ARNOTT FRONT AIR STRUT DODGE RAM 1500 (DS/DJ) | | | --- | --- | | 7. LOOSEN AND REMOVE THE NUT AND BOLT FROM THE BOTTOM STRUT FORK. (FIGURE 6)

FIGURE 6
8. LOOSEN AND REMOVE THE AIR FITTING FROM THE TOP OF THE STRUT. (FIGURE 7)

FIGURE 7
9. LOOSEN AND REMOVE THE THREE TOP STRUT MOUNTING NUTS. (FIGURE 8)

FIGURE 8 |

FAQs

Who should perform the removal and installation of this air suspension product?

Removal and installation should only be performed by fully qualified, ASE-certified professionals.

What safety step is required before disassembly of the air suspension system?

Verify pressure has been relieved and disconnect power to the air suspension system prior to disassembly.

What is the overall sequence flow from removal to installation?

Set steering straight ahead, raise the vehicle, remove the applicable front wheel and components for strut removal, then install the new strut and air fittings, tighten nuts to specifications, reinstall the wheel, lower the vehicle, and confirm installation completion.

Oct 22, 2026

Uploaded by Jacob