AS 1100.301 - 2008 - Technical drawing - Part 301 - Architectural drawing

Oct 28, 2026

AS 1100.301 specifies conventions for technical drawing focused on architectural drawings, providing a common method to represent buildings and their components so drawings can be prepared and interpreted unambiguously. It was prepared by Committee ME-072, approved in 2008 and published 2 December 2008. The publication incorporates Amendment No. 1 (May 2011) and includes a reconfirmation notice confirming its continued validity in 2018 while advising users to check for updates to referenced documents.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages9

Reading Time23 min

AccessFree to download

Reconformation and notice

Technical Committee review and continued validity

Ensuring users use latest referenced documents

Standard identification and publication history

Incorporating Amendment No. 1

First publication and redesignation

Scope and objective

Common method for representing buildings and components

Standards Australia maintenance and currency

Periodic review, amendments, and possible withdrawal

Rights and reproduction restrictions

Publisher and licence details

AS 1100.301—2008 (Incorporating Amendment No. 1) Reconfirmed 2018 AS 1 100 . 30 1—2008 Australian Standard® Technical drawing Part 301: Architectural drawing This Australian Standard® was prepared by Committee ME-072, Technical Drawing. It was approved on behalf of the Council of Standards Australia on 17 September 2008. This Standard was published on 2 December 2008. The following are represented on Committee ME-072: • Australian Institute of Quantity Surveyors (AIQS) • Department of Defence (Australia) • Department of Employment and Technical and Further Education, SA • Engineers Australia • Master Builders Australia • TAFE NSW • University of Adelaide • University of Melbourne • University of New South Wales • University of South Australia This Standard was issued in draft form for comment as DR 08023. Standards Australia wishes to acknowledge the participation of the expert individuals that contributed to the development of this Standard through their representation on the Committee and through the public comment period. Keeping Standards up-to-date Australian Standards® are living documents that reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions , amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments that may have been published since the Standard was published. Detailed information about Australian Standards, drafts, amendments and new projects can be found [by visiting](by visiting www.standards.org.au)[ www.standards.org.au](by visiting www.standards.org.au) Standards Australia welcomes suggestions for improvements, and encourages readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at [mail@standards.org.au](mail@standards.org.au), or write to Standards Australia, GPO Box 476, Sydney, NSW 2001. AS 1100.301–2008 (Reconfirmed) 2018-03-29 STANDARDS AUSTRALIA RECONFIRMATION OF AS 1100.301–2008 Technical drawing Part 301: Architectural drawing RECONFIRMATION NOTICE Technical Committee ME-072 has reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change. Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice. Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 12 March 2018. The following are represented on Technical Committee ME-072: The University of New South Wales Department for Education and Child Development (SA) University of South Australia Australian Institute of Architects NOTES AS 1100.301—2008 (Incorporating Amendment No. 1) Australian Standard® Technical drawing Part 301: Architectural drawing First published as AS 1100.13—1978 and AS 1100.301 Supp 1—1986. AS 1100.13—1978 revised and redesignated AS 1100.301—1985. AS 1100.301—1985 and AS 1100.301 Supp 1—1986, amalgamated, revised and redesignated AS 1100.301—2008. Reissued incorporating Amendment No. 1 (May 2011) . COPYRIGHT © Standards Australia Limited All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher, unless otherwise permitted under the Copyright Act 1968. Published by SAI Global Limited under licence from Standards Australia Limited, GPO Box 476, Sydney, NSW 2001, Australia ISBN 0 7337 8956 0 AS 1100.301—2008 2 PREFACE A

FAQs

What is AS 1100.301 mainly intended to achieve for architectural drawings?

It provides a common method for representing buildings and their components, enabling preparation and unambiguous interpretation of architectural drawings.

Who prepared and approved AS 1100.301, and when was it published?

It was prepared by Committee ME-072, Technical Drawing, approved on behalf of the Council of Standards Australia on 17 September 2008, and published on 2 December 2008.

Does AS 1100.301 include changes after its original 2008 publication?

Yes. The standard incorporates Amendment No. 1 (May 2011), with changes identified in the text by a marginal bar and amendment number.

Oct 28, 2026

Upload by FajarTechTalk