ARNOTT REAR AIR SPRING - Manual - BMW 5 SERIES (F07/F11 CHASSIS) - Air Suspension Products - Installation

Oct 22, 2026

Upload by Mia

Installation manual for an Arnott rear air spring air suspension product designed for BMW 5 Series (F07/F11 chassis). The document outlines prerequisites and safety requirements, including agreeing to the general release and liability waiver, proper vehicle lifting and immobilization, and pressure relief before disassembly. It instructs that removal and installation must be performed by fully qualified professionals and provides step-by-step procedures for air spring removal and installation, emphasizing correct disconnection, handling of air lines, and tightening fasteners to manufacturer specifications.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages5

Reading Time13 min

AccessFree to download

General Information

Air Spring Removal

Air Spring Installation

| A-2780
Installation
ARNOTT REAR AIR SPRING
Manual
BMW 5 SERIES(F07/F11 CHASSIS)
Air Suspension Products | | | --- | --- | | Congratulations on your purchase of an Arnott air suspension product.We at Arnott Incorporated are proud
to offer a high quality product at the industry's most competitive pricing.Thank you for your confidence in us
and our product.
Proper installation is essential to experience and appreciate the benefits of this system.Please take a moment
to review these installation instructions before you begin to install these components on your vehicle.The
removal and installation of air suspension products should only be performed by a fully qualified,ASE
Certified,professional.
It is equally important to be aware of all necessary safety measures while installing your new Air Suspension
System.This includes proper lifting and immobilizing of the vehicle and isolation of any stored energy to
prevent personal injury or property damage.
"Engineered to Ride,Built to Last"
WARNING:The air suspension system is under pressure(up to 10 bar,or 150 /bf/in).Verify pressure has been relieved
and disconnectpowerto the air suspension system prior to disassembly.Do not allow dit or grease to enter the system.
Always wear standard hand,ear,and eye protection when servicing the air suspension system.
Arnott is committed to the quality of its products.If you have a question or problem with any Arnott product,
please contact Arnott by calling 800-251-8993 during normal business hours or email techassistance@arnottinc.com. | | | 1 | A-2780
03/16/2016
REV 2 | | A-2780
Installation
ARNOTT REAR AIR SPRING
Manual
BMW 5 SERIES(F07/F11 CHASSIS)
Air Suspension Products | | | --- | --- | | GENERAL INFORMATION:
Reading this manual signifies your agreement to the terms of the general release,waiver of liability,and hold harmless agreement,
the full text of which is available at www.arnottinc.com.
·Not to be stored below 5°F(-15℃)or above 122°F(50℃).
·Avoid damage to air lines and cables.
· Removal and installation is only to be performed by fully qualified personnel.
·Use car manufacturer's diagnostic software.
CAUTION:Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified
in the instructions orin a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to
disconnect your battery.
Consult your vehicle owner's manual,service manual,or car dealer for the correct jacking points on your vehicle and for
additional care,safety and maintenance instructions.Under no circumstances should any work be completed underneath
the vehicle if it is not adequately supported,as serious injuries and death can occur.
AIR SPRING REMOVAL
SET STEERING TO STRAIGHT AHEAD.
1.
2.
RAISE VEHICLE.
3. REMOVE REAR WHEEL.(FIGURE 1)
FIGURE 1 | | | 2 | 03/16/2016
REV 2
A-2780 | | A-2780
Installation
ARNOTT REAR AIR SPRING
Manual
BMW 5 SERIES (F07/F11 CHASSIS)
Air Suspension Products | | | | --- | --- | --- | | 4.
LOOSEN AND REMOVE THE FASTENERS HOLDING THE REAR LOWER PLASTIC SHIELDTO EXPOSETH
VEHICLE'S AIR SUSPENSION COMPRESSOR.(FIGURE 2,3)
FIGURE 3
FIGURE 2
5.
LOCATE THE VALVE BLOCK NEAR THE COMPRESSOR ON THE REAR SIDE OF THE VEHICLE.REMOVE
THE APPLICABLE AIR LINE TO DEFLATE THE REAR AIR SPRING.(FIGURE 4,5)
FIGURE 5
FIGURE 4
6.
AFTERTHE AIR SPRING HAS DEFLATED,UNCLIPTHE LOWER PISTON BY SQUEEZINGTHE LOCKINGTA
TOGETHER AND PULLING UPTO FREE IT FROMTHE LOWER AIR SPRING PERCH.(FIGURE 6,7)
FIGURE6
FIGURE 7 | | E
BS | | 3 | REV 2
A-2780
03/16/2016 |

FAQs

Who is allowed to perform the removal and installation of the air suspension products?

Removal and installation should only be performed by fully qualified, ASE Certified professionals.

What safety steps must be followed before disassembling the air suspension system?

Verify that system pressure has been relieved and disconnect power to the air suspension system before disassembly, while also using proper lifting, immobilization, and energy isolation.

What should be done during air spring installation regarding the order and fastener tightening?

Installation is performed in reverse order of air spring removal, and all nuts and bolts must be tightened to the manufacturer’s specifications.

Oct 22, 2026

Upload by Mia