Accessories Manual - ProSet XT1 and ProSet XT2 Blind Rivet Tool Accessories - Safety Rules

Oct 29, 2026

ProSet XT1 and ProSet XT2 blind rivet tool accessory guidance covers intended use for placing Stanley Engineered Fastening blind rivets and details swivel head nose assemblies supplied separately for fitting to the base tool. The manual emphasizes reading safety warnings and operating instructions and provides selection criteria using rivet capability tables. It also supplies dimensions to assess application accessibility and lists procedures for preparing the base tool, including disconnecting the air supply before fitting or removing swivel head nose assemblies.

LanguageEnglish

CategoryTechnology

FormatPDF

Pages15

Reading Time38 min

AccessFree to download

Intent of Use

Straight & Right Angled Swivel Head Nose Assemblies

Table 1 - Straight Swivel Head Capability

Table 2 - Right-Angle Swivel Head Capability

Preparing the Base Tool to Accept Swivel Head Equipment

Accessories Manual Original Instruction ProSet® XT1 Blind Rivet Tool – 76001 ProSet® XT2 Blind Rivet Tool – 76002 Hydro-Pneumatic Power Tool STANLEY Engineered Fastening policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice Safety Rules | This technical datasheet must be read with particular attention to the safety warnings and operating instructions listed in the ProSet XT1 and ProSet XT2 Instruction Manual, by any person fitting or operating the nose assemblies and hand tools.
Intent of Use | | --- | | The accessories in combination with the ProSet XT1 and ProSet XT2 tools are designed for placing Stanley Engineered Fastening blind rivets only.
Straight & Right Angled Swivel Head Nose Assemblies | Swivel Heads are supplied separately for fitting to a base tool. Jaws and nose tips vary depending on the rivet tobe placed , but all other components remain the same within each type of swivel head. Refer to the rivet capability tables 1 below and table 2 on page 3 to select the correct swivel assembly for the rivet to be placed. For the Constant components refer to table 3 on page 6. Dimensions ‘A’ and ‘B’ in Tables 1 & 2 and fig. 1, 2 , 3 and 4 will help assess the accessibility of the application. | Table 1-STRAIGHT SWIVEL HEAD Capability | | | | | | | | | | --- | --- | --- | --- | --- | --- | --- | --- | --- | | RIVET
TYPE | RIVET
DIAMETER | | RIVET
MATERIAL | SWIVEL
HEAD | NOSE
TIP | DIMENSIONS | | JAWS | | | | | | | | A | B | | | AVEX | 3.2 | 1/8 | AL. ALLOY | 76003-06000 | 07345-03600 | 7.87 | 3.81 | 07340-00213 | | | 3.2 | 1/8 | STEEL | 76003-06100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.0 | 5/32 | AL. ALLOY | 76003-06100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.0 |

5/32 | STEEL | 76003-06200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | | 4.8 | 3/16 | AL. ALLOY | 76003-06200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | BULBEX | 4.0 | 5/32 | AL. ALLOY | 76003-06100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.8 |
3/16 | AL. ALLOY | 76003-06200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | AVINOX | 3.2 | 1/8 | ST. STEEL | 76003-06100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.0 |

5/32 | ST. STEEL | 76003-06200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | AVSEAL II | 4.0 | - | AL. ALLOY | 76003-06300 | 71213-16401 | 6.35 | 1.95 | 07340-00213 | | | 4.0 | - | AL. ALLOY | 76003-06400 | 71213-16402 | 6.35 | 4.11 | 07340-00213 | | | 5.0 | - | AL. ALLOY | 76003-06500 | 71213-16403 | 7.62 | 2.00 | 07340-00213 | | | 5.0 | - | AL. ALLOY | 76003-06600 | 71213-16404 | 7.62 | 4.11 | 07340-00213 | | STAVEX | 3.2 | 1/8 | STEEL | 76003-06100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.0 |
5/32 | STEEL | 76003-06200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | | 3.2 | 1/8 | ST. STEEL | 76003-06100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.0 |

5/32 | ST. STEEL | 76003-06200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | Table 2-RIGHT-ANGLE SWIVEL HEAD Capability | | | | | | | | | | --- | --- | --- | --- | --- | --- | --- | --- | --- | | RIVET
TYPE | RIVET
DIAMETER | | RIVET
MATERIAL | SWIVEL
HEAD | NOSE
TIP | DIMENSIONS | | JAWS | | | | | | | | A | B | | | AVEX | 3.2 | 1/8 | AL. ALLOY | 76003-07000 | 07345-03600 | 7.87 | 3.81 | 07340-00213 | | | 3.2 | 1/8 | STEEL | 76003-07100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.0 | 5/32 | AL. ALLOY | 76003-07100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.0 |

5/32 | STEEL | 76003-07200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | | 4.8 | 3/16 | AL. ALLOY | 76003-07200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | BULBEX | 4.0 | 5/32 | AL. ALLOY | 76003-07100 | 07345-03700 | 7.87 | 3.81 | 07340-00213 | | | 4.8 |
3/16 | AL. ALLOY | 76003-07200 | 07345-03800 | 7.87 | 3.81 | 07490-04602 | | AVINOX

FAQs

What is the intended use of these accessories with ProSet XT1 and ProSet XT2?

They are designed for placing Stanley Engineered Fastening blind rivets only.

How should you select the correct swivel head assembly for a given rivet?

Use the rivet capability tables (Table 1 and Table 2) and Table 3 for constant components to match the rivet type and specifications.

What safety step must be taken before fitting or removing swivel head nose assemblies?

Turn off or disconnect the air supply before fitting or removing the swivel head nose assemblies.

Oct 29, 2026

Upload by RuangKosong