[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-557876-105":59,"doc-detail-557876-en":130},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":123,"head_meta":125,"extra_data":127,"updated_unix":129},105,"en","white-paper-mating-connectors-iec-60320-standard-criteria-and-plug-outline-combinations","White Paper Mating Connectors - IEC 60320 - Standard Criteria and Plug Outline Combinations","","White Paper Mating Connectors explains IEC 60320 connector matching criteria, including how rated current replaces nominal current and how pin temperature TP is defined and limited by the standard (up to 70°C, 120°C, or 155°C). It describes operating ambient temperature assumptions and clarifies that pin temperature is driven mainly by appliance design and internal temperature rather than external ambient conditions. It further details general requirements such as withdrawal forces, testing procedures, minimum plugging cycles, and flexion counts for flexible cords, then organizes supported connector plug outlines and their permitted combinations into multiple tables for IEC 60320-1 and IEC 60320-2-2.",{"@graph":69,"@context":122},[70,84,105],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":40,"@type":76,"position":81},"https://docshare.wps.com/document/research-report/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/white-paper-mating-connectors-iec-60320-standard-criteria-and-plug-outline-combinations/557876/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/white-paper-mating-connectors-iec-60320-standard-criteria-and-plug-outline-combinations/557876.png","ImageObject",300,407,{"name":92,"@type":93},"Himbo","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-17","2026-10-12",true,{"@type":102,"interactionType":103,"userInteractionCount":44},"InteractionCounter",{"@type":104},"ViewAction",{"@type":106,"mainEntity":107},"FAQPage",[108,114,118],{"name":109,"@type":110,"acceptedAnswer":111},"What does the IEC 60320 standard use instead of “nominal current”?","Question",{"text":112,"@type":113},"It uses the term “rated current,” defining the current level the manufacturer designed the appliance coupler for.","Answer",{"name":115,"@type":110,"acceptedAnswer":116},"How is pin temperature TP measured and what limits apply?",{"text":117,"@type":113},"TP is measured where the pin projects from the engagement surface, with maximum permitted pin temperatures specified by the standard as 70°C, 120°C, and 155°C.",{"name":119,"@type":110,"acceptedAnswer":120},"Why is pin temperature determined mainly by appliance design rather than ambient temperature?",{"text":121,"@type":113},"The document states that pin temperature depends essentially on the appliance’s interior temperature design (TA2) rather than on the normal ambient temperature during operation (TA1).","https://schema.org",{"og:url":83,"og:type":124,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":126,"canonical":83},"index,follow",{"doc_id":128,"site_id":62},557876,1792484833,{"code":4,"msg":5,"data":131},{"doc_id":128,"user_id":132,"nickname":92,"user_avatar":133,"doc_module":4,"category_id":39,"category_name":40,"doc_title":65,"doc_description":67,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":44,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":81,"language":139,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":140,"faqs":141,"seo_title":142,"seo_description":67,"update_tm":143,"read_time":39,"preview_page_count":81,"preview_urls":144},687197100911,"https://ap-avatar.wpscdn.com/avatar/a000239b6f1da00475?x-image-process=image/resize,m_fixed,w_180,h_180&k=1785132997149421697","White Paper Mating Connectors  \n[www.schurter.com/downloads](www.schurter.com/downloads)  \nTable 1: Standard's definition  \nTable 1 shows the various main criteria and their specific values according to the standard's definition.  \nNominal current: The standard, instead of'nominal current', uses the term 'rated current'. It defines the current for which the manufacturer has designed the appliance coupler.  \nPin temperature TP is measured where the pin projects from the engagement surface (Figure 5) . The maximum permitted pin temperatures are, according to the standard, 70°C, 120°Cand 155°C, respectively. The appliance's normal ambient temperature TA1 during operation, according to IEC 60320, is 25°C and may occasionally reach 35°C. In other words, the pin temperature is determined essentially by the design of the respective appliance, i.e. its interior temperature TA2 , rather than by its ambient temperature. Typical applications with increased pin temperatures include appliances with heating coils such as ovens or electric grills.  \nconductor and special insulation.  \nIn addition to the limiting values described, the standards define further general criteria such as withdrawal forces, testing procedures, the minimum number of plugging cyclesand the number of flections in flexible cords. IEC 60320-1 codes the various plug outlines using a combination of letters and numbers (e.g. 'C14'), while IEC 60320-2-2 uses a single letter (e.g. 'F') .  \nTables 2, 3 and 4 describe the individual plug outlines in detail (Symbol, Type), i.e. their relevant nominal/rated current, pin temperature and protection class parameters. They also show which combination the standard defines. Each possible combination in the matrix is denoted with a dot. The columns list the components with the pins, while the lines show the sockets.  \nNormaly the parameter of inlet and outlet are similar ([e.g. protection](e.g. protection) class 1 -> 1) . It is generally possible to match a connector with a higher rated temerature with a lowe rated inlet.  \nGST Products  \n4  \nWhite Paper Mating Connectors  \n[www.schurter.com/downloads](www.schurter.com/downloads)  \n\n| Mating Appliance Coupler IEC 60320-1 |  |  |  |  |  | Appliance Inlets |  |  |  |  |  |  |  |  |  |  |  |  |\n| --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- |\n|  |  |  |  |  |  | Gender Male |  |  |  |  |  |  |  |  |  |  |  |  |\n|  |  |  |  |  |  | Symbol | | | |  |  | | | | | |  | |\n|  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |\n|  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |  |\n|  |  |  |  |  |  | Type | C6 | C8 | C8p | C10 |  | C14 | C16 | C16A | C18 | C20 | C22 | C24 |\n|  |  |  |  |  |  | Current [A] | 2.5 | 2.5 | 2.5 | 6 |  | 10 | 10 | 10 | 10 | 16 | 16 | 16 |\n|  |  |  |  |  |  | Temperature [°C] | 70 | 70 | 70 | 70 |  | 70 | 120 | 155 | 70 | 70 | 155 | 70 |\n| IEC 60320\u003Cbr>Connectors | Gender Female | Symbol | Type | Current [A] | Temperature [°C] | Protection class | 1 | 2 | 2 | 2 |  | 1 | 1 | 1 | 2 | 1 | 1 | 2 |\n|  |  | | C5 | 2.5 | 70 | 1 | • |  |  |  |  |  |  |  |  |  |  |  |\n|  |  | | C7 | 2.5 | 70 | 2 |  | • |  |  |  |  |  |  |  |  |  |  |\n|  |  | | C7p | 2.5 | 70 | 2 |  |  | • |  |  |  |  |  |  |  |  |  |\n|  |  | | C9 | 6 | 70 | 2 |  |  |  | • |  |  |  |  |  |  |  |  |\n|  |  | | C13 | 10 | 70 | 1 |  |  |  |  |  | • |  |  | |  |  |  |\n|  |  | | C15 | 10 | 120 | 1 |  |  |  |  |  | | • |  | |  |  |  |\n|  |  | | C15A | 10 | 155 | 1 |  |  |  |  |  | | | • | |  |  |  |\n|  |  | | C17 | 10 | 70 | 2 |  |  |  |  |  |  |  |  | • |  |  |  |\n|  |  | | C19 | 16 | 70 | 1 |  |  |  |  |  |  |  |  |  | • |  | |\n|  |  | | C23 | 16 | 70 | 2 |  |  |  |  |  |  |  |  |  |  |  | • |\n\nTable 2: Combinations according to IEC 60320-1; 􀂟 Intended, ¨ Possible  \n\n| Mating Intercorrection Coupler IEC 6032-2-2 |  |  |  |  |  | lugs |  |  |  |  |  |  |  |\n| --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- |\n|","cbCainOE8kJc0wmt","https://ap.wps.com/l/cbCainOE8kJc0wmt","pdf",185603,"English","# Standard's definition\n## Rated current vs nominal current\n## Pin temperature limits and ambient conditions\n## General criteria and testing procedures\n# IEC 60320 connector coding and combinations\n## IEC 60320-1 plug outlines and matrix combinations\n## IEC 60320-2-2 couplers and outlet combinations\n## Summary tables (Tables 2-4)","[{\"question\":\"What does the IEC 60320 standard use instead of “nominal current”?\",\"answer\":\"It uses the term “rated current,” defining the current level the manufacturer designed the appliance coupler for.\"},{\"question\":\"How is pin temperature TP measured and what limits apply?\",\"answer\":\"TP is measured where the pin projects from the engagement surface, with maximum permitted pin temperatures specified by the standard as 70°C, 120°C, and 155°C.\"},{\"question\":\"Why is pin temperature determined mainly by appliance design rather than ambient temperature?\",\"answer\":\"The document states that pin temperature depends essentially on the appliance’s interior temperature design (TA2) rather than on the normal ambient temperature during operation (TA1).\"}]","White Paper Mating Connectors - IEC 60320 - Standard Criteria and Plug Outline Combinations | PDF",1791798966,[145,149,153],{"page_no":8,"url":146,"width":147,"height":148},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/aba437eb6e8ad7b6b16f400c0a11c2ae.webp",983,1390,{"page_no":14,"url":150,"width":151,"height":152},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/fdb68fda302466df6ba0ce35c252fe47.webp",982,1389,{"page_no":81,"url":154,"width":155,"height":156},"https://res-academy.cache.wpscdn.com/upload/kdocshare/2026-11-17/e4650624e92027a1128b2945384a89b6.webp",981,1387]