[{"data":1,"prerenderedAt":-1},["ShallowReactive",2],{"detail-sidebar-cat-0-en-105":3,"doc-seo-646478-105":59,"doc-detail-646478-en":130},{"code":4,"msg":5,"data":6},0,"success",[7,13,18,23,28,33,38,43,48,51,55],{"id":8,"doc_module":4,"doc_module_name":9,"category_name":10,"show_sort_weight":11,"slug":12},1,"Document","Story & Novel",90,"story-novel",{"id":14,"doc_module":4,"doc_module_name":9,"category_name":15,"show_sort_weight":16,"slug":17},2,"Literature",80,"literature",{"id":19,"doc_module":4,"doc_module_name":9,"category_name":20,"show_sort_weight":21,"slug":22},4,"Exam",70,"exam",{"id":24,"doc_module":4,"doc_module_name":9,"category_name":25,"show_sort_weight":26,"slug":27},5,"Comic",60,"comic",{"id":29,"doc_module":4,"doc_module_name":9,"category_name":30,"show_sort_weight":31,"slug":32},6,"Technology",50,"technology",{"id":34,"doc_module":4,"doc_module_name":9,"category_name":35,"show_sort_weight":36,"slug":37},7,"Healthcare",40,"healthcare",{"id":39,"doc_module":4,"doc_module_name":9,"category_name":40,"show_sort_weight":41,"slug":42},8,"Research & Report",30,"research-report",{"id":44,"doc_module":4,"doc_module_name":9,"category_name":45,"show_sort_weight":46,"slug":47},9,"Religion & Spirituality",20,"religion-spirituality",{"id":46,"doc_module":4,"doc_module_name":9,"category_name":49,"show_sort_weight":46,"slug":50},"World Cup","world-cup",{"id":52,"doc_module":4,"doc_module_name":9,"category_name":53,"show_sort_weight":52,"slug":54},10,"Lifestyle","lifestyle",{"id":56,"doc_module":4,"doc_module_name":9,"category_name":57,"show_sort_weight":24,"slug":58},19,"General","general",{"code":4,"msg":60,"data":61},"ok",{"site_id":62,"language":63,"slug":64,"title":65,"keywords":66,"description":67,"schema_data":68,"social_meta":123,"head_meta":125,"extra_data":127,"updated_unix":129},105,"en","om-823g-owners-manual-february-1992","OM-823G - Owner’s Manual - February 1992","","Owner’s manual for Miller Electric Mfg. Co. remote hand controls, including the RHC-3 family and related models listed in the document. Provides safety precautions and signal word explanations, then covers receipt and handling steps, model/serial recording, installation location and interconnections, and cord conductor length and size guidance. Includes references to operator control operation, electrical diagrams, and parts lists, supporting safe setup and effective use with welding power sources or generators.",{"@graph":69,"@context":122},[70,84,105],{"@type":71,"itemListElement":72},"BreadcrumbList",[73,77,79,82],{"item":74,"name":75,"@type":76,"position":8},"https://docshare.wps.com","Home","ListItem",{"item":78,"name":9,"@type":76,"position":14},"https://docshare.wps.com/document/",{"item":80,"name":35,"@type":76,"position":81},"https://docshare.wps.com/document/healthcare/",3,{"item":83,"name":65,"@type":76,"position":19},"https://docshare.wps.com/document/om-823g-owners-manual-february-1992/646478/",{"url":83,"name":65,"@type":85,"image":86,"author":91,"headline":65,"publisher":94,"fileFormat":97,"inLanguage":63,"description":67,"dateModified":98,"datePublished":99,"encodingFormat":97,"isAccessibleForFree":100,"interactionStatistic":101},"DigitalDocument",{"url":87,"@type":88,"width":89,"height":90},"https://docshare.wps.com/thumbnails/om-823g-owners-manual-february-1992/646478.png","ImageObject",300,407,{"name":92,"@type":93},"Aditya","Person",{"url":74,"name":95,"@type":96},"DocShare","Organization","application/pdf","2026-11-03","2026-10-23",true,{"@type":102,"interactionType":103,"userInteractionCount":24},"InteractionCounter",{"@type":104},"ViewAction",{"@type":106,"mainEntity":107},"FAQPage",[108,114,118],{"name":109,"@type":110,"acceptedAnswer":111},"What safety requirements does this manual emphasize before using the remote hand controls?","Question",{"text":112,"@type":113},"It instructs readers to read and understand the entire manual and the associated power source manual, with special emphasis on safety material. Installation, operation, and maintenance must be performed only by trained and experienced persons in safe operation of welding equipment.","Answer",{"name":115,"@type":110,"acceptedAnswer":116},"How should the equipment be checked when receiving and unpacking it?",{"text":117,"@type":113},"Before unpacking, check the carton for any damage from shipment and file claims for loss or damage with the delivering carrier. When requesting information, provide the model description and serial or style number.",{"name":119,"@type":110,"acceptedAnswer":120},"What cord specifications are recommended for different lengths and amperage/voltage ranges?",{"text":121,"@type":113},"The manual lists cord conductor sizes by control range and cord length in Table 2-1, including variants for GD models. If installing a longer multi-conductor cord, refer to the table for the correct conductor size.","https://schema.org",{"og:url":83,"og:type":124,"og:title":65,"og:site_name":95,"og:description":67},"article",{"robots":126,"canonical":83},"index,follow",{"doc_id":128,"site_id":62},646478,1792992396,{"code":4,"msg":5,"data":131},{"doc_id":128,"user_id":132,"nickname":92,"user_avatar":133,"doc_module":4,"category_id":34,"category_name":35,"doc_title":65,"doc_description":67,"doc_content":134,"file_id":135,"file_url":136,"file_type":137,"file_size":138,"view_count":24,"is_deleted":4,"is_public":8,"is_downloadable":8,"audit_status":8,"page_count":52,"language":139,"language_code":63,"site_id":62,"html_lang":63,"table_of_contents":140,"faqs":141,"seo_title":142,"seo_description":67,"update_tm":143,"read_time":144,"preview_page_count":4},962085564549,"https://ap-avatar.wpscdn.com/davatar_085a072bc5b1113ac321206ff7593b45","February 1992 FORM: OM-823G Effective With Serial No. KB055102  \nMODEL: RHC-3  \nRHC-3-2  \nRHC-3GD9A  \nRHC-3GD25B  \nRHCS-3  \nRHC-3-GD34A  \nRHC-14  \nRHC-23  \nOWNER’S MANUAL  \n\n| IMPORTANT: Read and understand the entire contents of both this manual and the power source manual used with this unit, with special emphasis on the safety material throughout both manuals, before installing, operating, or maintaining this equipment. This unit and these instructions are for use only by persons trained and experienced in the safe operation of welding equipment. Do not allow untrained persons to install, operate, or maintain this unit. Contact your distributor if you do not fully understand these instructions. | MILLER ELECTRIC Mfg. Co.\u003Cbr>A Miller Group Ltd. , Company\u003Cbr>P.O. Box 1079\u003Cbr>Appleton, WI 54912 USA Tel. 414-734-9821 |\n| --- | --- |\n\nSA-141 127 PRINTED IN U.S.A.  \nOM-823G-2/92  \n\n| RECEIVING-HANDLING |  |\n| --- | --- |\n| Before unpacking equipment, check carton for any damage that may have occurred during shipment. File any claims for loss or damage with the delivering carrier. Assistance for filing or settling claims may be obtained from the distributor and/or the equipment manufacturer’s Transportation Department.\u003Cbr>When requesting information about this equipment, always provide the Model Description and Serial or Style Number. | Use the following spaces to record the Model Designation and Serial or Style Number of your unit. The information is located on the rating label or nameplate.\u003Cbr>Model   Serial or Style No.   Date of Purchase   |\n\nTABLE OF CONTENTS  \nSection No. Page No.  \nSECTION 1 − SAFETY PRECAUTIONS AND SIGNAL WORDS  \n1-1. General Information And Safety ............................... 1  \n1-2. Safety Alert Symbol And Signal Words ......................... 1  \n1-3. Description ................................................. 1  \nSECTION 2 − INSTALLATION  \n2-1. Location .................................................... 1  \n2-2. Interconnections ............................................. 1  \nSECTION 3 − OPERATOR CONTROLS  \n3-1. Operation ................................................... 2  \n3-2. Contactor Switch ............................................ 2  \nSECTION 4 − MAINTENANCE  \nSECTION 5 − ELECTRICAL DIAGRAMS  \nDiagram 5-1. Circuit Diagram For Remote Hand Control Used With Transformer Arc Welding Power Source ................ 3  \nDiagram 5-2. Circuit Diagram For RHCS-3 .......................... 3  \nDiagram 5-3. Circuit Diagram For RHC-3-GD9A And RHC-3-GD34A .... 3  \nDiagram 5-4. Circuit Diagram For RHC-3-GD25B .................... 4  \nDiagram 5-5. Circuit Diagram For RHC-14 And RHC-23 ............... 4  \nSECTION 6 − PARTS LIST  \nFigure 6-1. Complete Assembly (RHC-3 Illustrated) ..................... 6  \nLIST OF CHARTS AND TABLES  \nTable 2-1. Cord Conductor Length And Size ........................... 1  \n\n| SECTION 1 − SAFETY PRECAUTIONS AND SIGNAL WORDS |  |  |\n| --- | --- | --- |\n| 1-1. GENERAL INFORMATION AND SAFETY\u003Cbr>A. General\u003Cbr>Information presented in this manual and on various labels, tags, and plates on the unit pertains to equipment design, installation, operation, maintenance, and troubleshooting which should be read, understood, and followed for the safe and effective use of this equipment.\u003Cbr>The nameplate of this unit uses international symbols for labeling the front panel controls. The symbols also appear at the appropriate section in the text.\u003Cbr>B. Safety\u003Cbr>The installation, operation, maintenance, and troubleshooting of arc welding equipment requires practicesand procedures which ensure personal safety and the safety of others. Therefore, this equipment is to be installed, operated, and maintained only by qualified persons in accordance with this manual and all applicable codes such as, but not limited to, those listed at the end of Section 1 − Safety Rules For Operation Of Arc Welding Power Source.\u003Cbr>1-2. SAFETY ALERT SYMBOL AND SIGNAL WORDS\u003Cbr>The following safety alert sym","cbCaigaBtJOkDzRZ","https://ap.wps.com/l/cbCaigaBtJOkDzRZ","pdf",562893,"English","# SECTION 1 − SAFETY PRECAUTIONS AND SIGNAL WORDS\n## 1-1. General Information And Safety\n## 1-2. Safety Alert Symbol And Signal Words\n## 1-3. Description\n# SECTION 2 − INSTALLATION\n## 2-1. Location\n## 2-2. Interconnections\n# SECTION 3 − OPERATOR CONTROLS\n## 3-1. Operation\n## 3-2. Contactor Switch\n# SECTION 4 − MAINTENANCE\n# SECTION 5 − ELECTRICAL DIAGRAMS\n## Diagram 5-1. Circuit Diagram For Remote Hand Control Used With Transformer Arc Welding Power Source\n## Diagram 5-2. Circuit Diagram For RHCS-3\n## Diagram 5-3. Circuit Diagram For RHC-3-GD9A And RHC-3-GD34A\n## Diagram 5-4. Circuit Diagram For RHC-3-GD25B\n## Diagram 5-5. Circuit Diagram For RHC-14 And RHC-23\n# SECTION 6 − PARTS LIST\n## Figure 6-1. Complete Assembly (RHC-3 Illustrated)","[{\"question\":\"What safety requirements does this manual emphasize before using the remote hand controls?\",\"answer\":\"It instructs readers to read and understand the entire manual and the associated power source manual, with special emphasis on safety material. Installation, operation, and maintenance must be performed only by trained and experienced persons in safe operation of welding equipment.\"},{\"question\":\"How should the equipment be checked when receiving and unpacking it?\",\"answer\":\"Before unpacking, check the carton for any damage from shipment and file claims for loss or damage with the delivering carrier. When requesting information, provide the model description and serial or style number.\"},{\"question\":\"What cord specifications are recommended for different lengths and amperage/voltage ranges?\",\"answer\":\"The manual lists cord conductor sizes by control range and cord length in Table 2-1, including variants for GD models. If installing a longer multi-conductor cord, refer to the table for the correct conductor size.\"}]","OM-823G - Owner’s Manual - February 1992 | PDF",1792762410,25]